Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Conference & Discussion

    Sort by:
    ‎04-06-2021 11:58 AM
    A participant who uses a seat with Priority permissions set was not able to use the Priority button and interrupt other participants in the meeting.
    View full article
    ‎11-08-2022 02:21 PM
    Symptoms: When a meeting is recorded and the recording software (either Meeting Recorder or Open Interface connection) is shut down, the microphone control mode switches to "Open", independent of what it was before.
    View full article
    ‎04-06-2021 12:17 PM
    A DCN-NG system is installed with a DCN-WAP but needs to be expanded and an extra WAP needs to be added. Is this possible?
    View full article
    2 weeks ago
    DICENTIS installation log files are needed for further analysis for Technical support team if the software update failed or later some errors occurred. Below it is explained how you can extract DICENTIS installation log files.
    View full article
    ‎04-06-2021 11:56 AM
    Product(s) affected: DCN-NG systems with master & slave CCU set-up Version(s): all Problem description: A DCN-NG system will be installed in a building which uses different VLANs for different floors in the building. They want to be able to have interpreters on one floor (in one VLAN) and the rest of the system on another floor (in another VLAN). To this end they have connected their Master CCU to another VLAN than their Slave CCU. This set-up does not work. Question is; should this work and if not, why not? Solution: This cannot work in a DCN-NG system because of the way the system is designed. The communication between the CCU’s, at start-up of the system, uses broadcast messages which are not routed by network devices. These messages have a time-to-live (TTL) of 1, which means that once they attempt to cross into another (V)LAN, the messages are not propagated by the routing (L3) switch. The reason is that the TTL of the packet is decreased every time it traverses from one network to another. When the TTL’s value reaches 0, the packet is dropped by the routing device. Therefore, the broadcast packet will never reach the other CCU, resulting in error messages like “No Master CCU” on the Slave CCU. Therefore the system should be installed on the same (V)LAN. This usually does not pose any technical problems as (V)LANs can be distributed over multiple network devices without issue, it’s just that the predictability of where a device is physically located is less in this instance.
    View full article
    2 weeks ago
    In some cases the log file from the Dicentis Server become too big and it has to be cleared to reduce the size from time to time. The normal size is between 10MB and 50MB depending on the operation time but it should normally not grow over 100MB. If it does exceed, is most likely a fatal error within the DICENTIS system which produce a lot of logging each minute. It could be possible that the driver of the Network Card (3rd party Server) to become intermittent and the log file to grow to 300MB. In the next steps we will show you how to clear the logging.
    View full article
    ‎08-24-2021 05:20 PM
    Possible causes and solution(s) Causes   The Dicentis does not need any additional encryption to be set via the OMNEO Firmware Upload Tool. (OFUT) If you have set this by accident it could lead to that you can not see or update your units with the OFUT any more.   Solution:   stop the Firmware Upload Tool delete the following file  C:\Program Files\Bosch\OMNEO\Firmware Upload Tool\FirmwareUploadHIConfig.ini start the Firmware Upload Tool   Encrypted devices did not show up and you can not update them anymore. Do not set a password for default!   Open and delete this file  C:\Program Files\Bosch\OMNEO\Firmware Upload Tool\FirmwareUploadHIConfig.ini   Open the OFUT and units will appear again.  
    View full article
    ‎12-13-2022 03:04 PM
    This article explains step by step wow to enable web server configuration for PRA-ES8P2S.
    View full article
    ‎01-03-2023 08:20 AM
    If you can't see the DICENTIS Server Console Item in the right tab anymore this article will help you to surface them again.
    View full article
    ‎06-30-2021 11:10 AM
    In some cases, especially if you use a 3rd party PC as DICENTIS Server, it could be necessary to update your network driver. For example, if discussion units show a red LED from time to time or your DICENTIS is dropping out it could be related to the network driver. Be aware that a normal Windows Update will not refresh this driver and you have to update it manually!
    View full article
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist