Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    How to configure IP-223 for Console Mode

    Question

    How do I configure the IP-223 to operate in Console mode?

     

    Answer

    Programming the IP-223 to operate in Console mode:

    For either 2 or 4 wire set J3, J9, J11, J16 and J21 (Line 1) or J19, J20, J25, J28 and J29 (Line 2) to "B" position.

    For 2-Wire; set J33 and J34 (Line 1) or J5 and J6 (Line 2) to "A" position, set J14 (Line 1) or J24 (Line 2) to "B" position.

    For 4-Wire set J33 and J34 (Line 1) or J5 and J6 (Line 2) to "B" position, set J14 (Line 1) or J24 (Line 2) to "A" position.

    Close unit
     
    Now connect your 2 or 4-Wire control line to the correct IP-223 DB-25 I/O port.

    For 2-Wire connect the (TX/RX) wires to Pins 13 and 25

    For 4-Wire connect the TX (Out to console) wires to Pins 13 and 25, connect the RX (In from console) wires to Pins 12 and 24.


    Once your jumpers and wire connections are set you will need to place the IP-223 line into Console mode. To do this, follow the steps below:

    Log into the web page of the IP-223.

    Click on the Multicast address setup picture at the top of the page.

    Use the Line Type drop down for line 1 or line 2 and set it to Console mode.

    Now Click on the Submit button at the bottom of the page.

    Click on the Per-Line setup picture at the top of the page.

    Go to individual Lines being configured for Console mode, scroll down to "Options" section.

    Check "Parallel Tone Console" checkbox.

    Now Click on the Submit button at the bottom of the page.

    Now click on the Save To EEPROM and click on Save Parameters.

    Now that line of the IP-223 is set to Console mode will decode PTT tones.


    The next steps you need to take is to set levels. To set levels do the following:

    Using a transmission test set or similar device, measure the audio on the front panel RX test point of the IP-223 to ground.

    Key up the attached tone console, with no voice (only 2175 tone present)

    Using a small screw driver, adjust the RX pot on the front of the IP-223 for the line under test. 

    Set the Low Level guard tone to the level you desire, typical is -20dbm into a loaded circuit (looking for 0 gain)

    Key up the tone console, measure the voice audio on the RX pins of the IP-223, typical is 0dbm peaks into a loaded circuit.

    You should see "CTX F1" displayed on the front of the IP-223 when you PTT from the tone console, TX packets are now being sent to the network.

     

     

     

     

     

    © Copyright Bosch Security Systems

    All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights.

    Warranty Note

    This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.

     

    Version history
    Last update:
    ‎04-08-2020 06:23 PM
    Updated by:
    Labels (1)
    Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist