Fire

Part numbers D10024A, D10024, D9024, D8024

Perform these steps to enable the D7024, FPD-7024, DS9400, DS9400I, and DS9400M for RPS programming via phone line with a compatible RPS modem: Press (0) Enter Program Mode. Enter Pin (Default is 9876). Press (6) Accounts. Press (4) Ring Count. Set Ring Count to (02) #. Press the (*) key two times or until you see PROGRAM MODES. Press (3) System. Press (7) Remote Program. Press (1) Enable. Press the (*) key five times to Exit Program Mode. You need to dial Line 1 on the panel. It is the second line down on the panel (it is NOT the line in the top right). Before connecting with RPS, perform an Auto-Learn with at least one Mux Device connected to the Mux loop, then send your RPS program to the panel. Press (0) Enter Program Mode. Enter Pin (default is 9876). Press (9) Program Mux. Press (4) Auto Program. Press (1) Yes.

Panel part numbers - FPD-7024, FPA-1000, FPA-1000-UL, and FPA-1000-V2. Network Card part numbers for the FPD-7024, DX4020, B420, and B426. Cellular option for the FPD-7024 part numbers B450 (Interface for Cellular Card) B440, B441, B442, B443, and B444.

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7465, DS7465i, D8125MUX, D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G, B600, D5060, D7053, FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part Numbers D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, D192C, D192G

Part numbers D5200, D9124, D9124G, D9124GLTB, D9124GV2, D9124GV2LTB

Part numbers FPD-7024,  D7024, DS9400, DS9400I, DS9400M, D7053, D7035, DS9465I, MX465, DS9432,

Part mumbers D9068, D9052, D8024, D9024, D40024, D10024A, D7033, FMR-DACT-KEYPAD

How to upgrade the D5070 Programmer to program addresses 128 through 254.

Part numbers D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G, B600, D8125INV, FA400

The D132B is a multipurpose, fully configurable, smoke power-reversing module for activating detectors with local annunciation. The module will operate both two-wire and four-wire 24 V circuits, and also works with Class A or Class B initiating circuits. An alarm latch connection is provided to allow an initiating loop to be held in alarm after the detector loop power has been reversed to activate any sounders. The module does not affect compatibility between the FACP and detectors, or the FACP and notification appliance circuits (NACs). The maximum current available from the FACP smoke power terminals or NACs limits the total number of reversible smoke detectors that can be connected to the module. Consult the FACP’s installation instructions for compatibility with the D132B Multi-Use Reversing Relay Module. Part numbers D132B, D7024, FPD-7024

Part numbers D461, D102, D102E

Part Numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER3+, DS7400XIVER4+, DS7400XIVER2, DS7447I, DS7447E, DS7447

Part numbers - FPA-1000, FPA-1000-UL, FPA-1000-V2, FLM-325-CZM4

Perform a sesitivity test on the following MUX smoke heads, D7050, D7050TH, D7050DH, MX250, MX250TH & MX250DH.

Part numbers D293S, D285, D285TH, D603, D604, D605, D275

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7447, DS7447E

Part number D9133TTL-E, C900TTL-E

The following horn strobes and strobes are listed compatible with the DS9400, DS9400I, and DS900M Fire Control Panels:

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4, ARDIS