Fire

Programming the FPD-7024 to report via ethernet to the CS with a DX4020 Network Card.

The FLM-325-2i4 is a Single address Dual Input Analog Addressable Module with two inputs used to monitor Normally Open (NO) or Normally Closed (NC) circuits.  If the module is addressed as 010 the First input will display as 010.1 on the panel keypad display, the Second input will display as 010.2 on the panel keypad display. 

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, D8125MUX, D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G, B600, B299, D8125, FPA-1000, FPA-1000-V2, FPE-7039, D7039, DS9431, FDP-7024, D7024, DS9400, DS9400I, DS8400M, D10024A, D10024, D9024, D8024, D7212B, D9112B, D7212B1, D9112B1, D7212, DS7430, DS7436,

Part Numbers, FAD-325 (DUCT Housing without Relay), FAD-325-V2F (DUCT Housing without Relay), FAD-325-R (DUCT Housing with Relay), FAD-325-V2F-R (DUCT Housing with Relay) FML-325-2R4, FML-325-2R4-2A, FML-325-2R4-2AI, FML-325-2R4-8A, FML-325-2R4-8AI, D323DH (DUCT Smoke Head), FAD-325-DH (DUCT Smoke Head), FAD-325-V2F-DH, FPA-1000, FPA-1000-UL, and  FPA-1000-V2.

Part numbers FPA-1000, FPA-1000-V2, FPE-1000-NE, FPE-1000-NW, FPR-1000-NF  

Question What does it mean when the panel displays a trouble of "Dialer Answering Unknown"?   Answer   "Dialer Answering Unknown" is caused by the panel answering an incoming phone call. This will cause a trouble tone from the panel that will clear itself when the panel releases the line, this may take up to 10 minutes. If another event (Alarm, Trouble, Supervisory) occurs during this time, the panel will drop the line and dial out to the central station. To prevent or stop this set the Line 1 Ring Count to (0).  

Part numbers FCP-500, FCP-500-C

Option Bus NAC Outputs (FPP-RNAC-8A-4C) will never be in sync with the NAC Output of the panel (FPA-1000, FPA-1000-UL, FPA-1000-V2, or FPD-7024).

This article contains the RCP+ CGI commands for AVIOTEC starlight 8000 that helps you to enable or disable the scene quality (bright or dark)

This article contains the RCP+ CGI command for AVIOTEC starlight 8000 that helps you to adjust the VCA darkness or brightness level

This article answer if the labels or texts automatically updated in FSM after change in RPS.  

This article answer to the question: " What is the maximum of simultaneous client connections supported on FSM?"

This article is a step by step guide about how to create panel container on map by using Macro-Area (point) on FMS.

How to replace existing map or background on FSM client?

Is it possible to use complex maps on the FSM client? Recommendation is not to use very complex maps, very complex maps (means big size DWG files) can be made “lighter” by reducing the number of vertex (e.g. remove texts in DWG file and make rather use of the FSM text feature)

How to Connect to a FPD-7024 locally using Enhanced Direct with a DX4010V2

This article answer to the question: Is the usage of command and digital properties function supported -FSM?

Is the status displayed when Supervisory Usage type is selected in RPS - Bosch Fire Monitoring System?

This article explains is we can use Remote desktop to run or use the FSM client. When using remote desktop the error below will be shown when remote desktop is minimized and then maximized, the only option is to close the FSM client and start again.

This article explain how it is possible to automatically zoom in the map in case of alarm.