Security: Intrusion

How to disable Call Waiting on D4412/D6412 Panels.

How to correct the D4412/D6412 only reporting to one destination and not following programmed routing.

The D4412 and D6412 use the D621, D623 or D625 command centers. Pressing All-On or Part-On on the will arm only the area where the keypad is assigned. Command 50 may be used to move to an area other than the programmed assigned area.  After moving to the selected area, press either All-on or Part-on to arm the area. Command 80 may be used to arm all areas. Command 81 may be used to disarm all areas. Note:  Commands 80 and/or 81 must be enabled by an individual with assigned authorization to perform the function. Use Command 50 to move to another area and arm:  Press [CMD] [5][0] and enter a valid code if required. The keypad will scroll through all available areas. Press the desired area number to move to the area.  Press All-On or Part-On to arm the selected area.  Pressing and holding [CMD] will exit the Command 50 feature returning the keypad to its “home” area. Use Command 80 to arm All Areas: Press [CMD] [8][0] and enter a valid code if required.       Hold down the All On key for 2 sec and it forces all areas to All On.  Use Command 81 to disarm All Areas:  Press [CMD] [8][1] and enter a valid code if required. The keypad will indicate all areas are off.

How to correct working points showing not programmed in RPS diagnostics.

Issue What keypads will work on the D6112?   Solution   Compatible keypads are: D420A, 6 zone LED. This will work but only the first six zones will be displayed. D620, 8 zone LED. D626, 16 zone LED. D630, 8 zone LED with 3 onboard expansion points. D636A, 16 zone alpha display with 3 onboard expansion points

Overview Set up of a D6112 panel to have keyswitch arming. D611 is required. *Note -   D611 is no longermade. Issue Keyswitch arming the D6112 panel. Solution D6112 panel can use a D611 Key Switch Module. The D611 connects to the panels serial device data wiring. (connects in series like a keypad) Panel programming: 4.1 Device#     =    location in the series wiring of the serialdevice data                               1,2,3,4. 4.2 D#Model   =   1 6.1 Combo3    =   8 Notes D4112, D6112, and the D611 no longer made.

How to: Determine if the D125B can be used with the D4412 or D6412.

How to control Disarm Authority in the D6412/D4412.

Issue What would cause the Armed LED to not function on an LED Command Center, while arming the system? Solution To correct the Armed LED try the following steps: 1. Recycle power to the command center, and the panel. 2. Readdress the command center, anything other than address one. Then reprogram the command center for the same address number, and reset the panel.

How to correct the D132A supervision point not showing normal circuit status.  Cannot get the onboard point from the D132A module to show normal circuit status. D132A,D4412,D6412,DS7220,DS7240,D2212

Issue What would cause the panel to send every report at one time? Solution Command 95 CMD 95 is the test function that will send all available reports. In the circumstance where a customer has set a code that begins with 95 such as (9595) and put in his code incorrectly, when re-entering, the customer would press the command key and 95 and the rest of the code causing the panel to send all reports to the central station resulting in a dispatch of emergency services. The work around if an updated chip is not available, change the first two digits from 95xx. This effected panel versions  1.08 - 1.11 The eeprom to correct this issue would be: 1.12

How to troubleshoot missing onboard points 1-8 on the D4412/D6412.

How to access View Point Status in the D4412/D6412. D4412,D6412,D623,D625

How to enable the Ground Fault display and trouble tone on the D6412/D4412.

How to Part Arm or Part 2 arm the D4412 or D6412.

Issue The D4412/D6412 panel reports zones (zones  10o,101,102)when reporting to a D6500 receiver sending Modem IIIa2.   Solution   Only the following central station receivers support the D6412/D4412 Modem IIIa2 Format: • D6600 with CPU v.01.01.03 (or higher) • D6500 with D6511 MPU v1.05 (or higher) .The D6500 with D6510 MPU does not support the D6412/D4412 Modem IIIa2 Format. Note: Normal operation when using the A,B,C keys, reporting is as follows: [A] key reports as Zone 100 for all areas [B] key reports as Zone 101 for all areas [C] key reports as Zone 102 for all areas

Issue How to make the CMD's not require a passcode in programming?   Solution   Nibbles 0364 - 0378 put a 0 in for keypad programming or with RAM software in USER INTERFACE, sub menu Authority Level Configuration, make all commands DISABLE under Authority Level 1 - 4.

How to disable reporting on a D4412/6412

Issue When using the Auto Arm Sked, the keypad shows a countdown timer counting down 30 minutes prior to arming. Solution Auto On Pre-Alert Time Nibble: 0233 Default: 6 (30 minutes) Selections: 0-15 (time = selection x 5 minutes; 0 = disabled) Parameter Description The pre-alert sounds before the Auto On Sked to warn users to exit or extend (Cmd 51) the auto arming. At the Auto On time, the panel starts exit delay. See Sked Type for a complete description of the Auto On Skeds. If the area is armed according to the scheduled arming state (All On or Part On) during Auto On Pre-Alert Time and then disarmed before the scheduled arming, auto-arming will not occur.

How to interpret a Battery Low report on the D4412/D6412. What battery voltage will the panel transmit a BATTERY LOW report?