Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    100% helpful (1/1)
    ‎05-23-2018 08:20 PM
    How can the command center be cleared after an alarm condition on the 7000/9000 series panels?  D7412G,D9412G,D9412,D7412,D7212,D7212G,D9412GV2,D7412GV2,D7212GV2,D9412GV3,D7412GV3,D7212GV3,D9412GV4,D7412GV4,D7212GV4,D1255,D1260
    View full article
    ‎07-02-2019 10:54 PM
    Menu access disabled when using TeraTerm and B450.
    View full article
    100% helpful (1/1)
    ‎07-23-2018 07:52 PM
    How to dim or brighten the display on the D1255 keypad?
    View full article
    100% helpful (1/1)
    ‎10-16-2018 09:43 PM
    How to work with duress passcodes and avoid ‘Passcode in Use’ errors. Why does ‘Passcode in Use’ display when adding a new code and how to prevent the message from displaying.
    View full article
    ‎07-30-2018 09:33 PM
    How to access the IP Communicator Web Browser.
    View full article
    100% helpful (1/1)
    ‎05-23-2018 08:19 PM
    The panel is dialing in Pulse when its programmed to dial in DTMF. How to make the panel dial in DTMF when programmed for DTMF but still dialing in Pulse.
    View full article
    ‎10-23-2019 05:13 PM
    What are Point Indexes and how are they used to program points on D7212, D7412 or D9412 G-GV4 panel types? How to program the D7212, G, GV2, GV3 or GV4 How to program the D7412, G, GV2, GV3 or GV4 How to program the D9412, G, GV2, GV3 or GV4
    View full article
    ‎06-08-2018 03:22 PM
    How to arm or disarm a single area using a keypad with scope in all areas. When all areas are disarmed, associate areas can be armed independantly. But when attempting to disarm, associate areas keep rearming instead of disarming.
    View full article
    ‎05-15-2018 04:45 PM
    How to Identify the firmware revision of an intrusion panel.
    View full article
    100% helpful (1/1)
    ‎06-04-2018 05:22 PM
    Determine compatibility of the wireless interface with the panel type and firmware revision.   B820 Wireless interface and EN4200 receiver. Compatible with GV4 panel types, B-Series panels and B8512G/B9512G. The B820 connects to the SDI2 Bus. ISW-D8125CW-V2 Wireless interface and EN4200 receiver. Compatible with G series with rev6.3+ through GV4 when connected to the Zonex bus or B8512G/B9512G when using the B600 retrofit module. ISW-D8125CW Wireless interface and ISW-EN7280 (ISW-TRL8080/ISW-EN4200) receiver. Compatible with G series with rev6.3+ through GV4 when connected to the Zonex bus or B8512G/B9512G when using the B600 retrofit module. D8125INV Wireless interface and FA400 receiver. Compatible with G series with rev6.3+ through GV4 when connected to the Zonex bus or B8512G/B9512G when using the B600 retrofit module. Determine compatibility of transmitters by the wireless interface type and receiver date code. EN4200 with date code 11048 and newer (date code is yyddd where yy=year and ddd=day): Works with transmitters designated with ENxxxx or ISW-ENxxxx part numbers. EN4200 with date code 11047 and older (date code is yyddd where yy=year and ddd=day): Works only with transmitters designated with ISW-ENxxxx part numbers. Compatible Transmitters designated with ENxxxx part numbers. Requires EN4200 with date code 11048 or newer; EN1223D Water‑resistant Pendant Panic EN1223S Water‑resistant Pendant Panic EN4200 Wireless receiver EN1233D Necklace Pendant Panic EN1233S Necklace Pendant Panic EN1235D Belt-clip Panic EN1235S Belt-clip Panic EN1235SF Fixed Location Panic EN1235DF Fixed Location Panic EN1210EOL Universal Transmitter w/ EOL EN1210W Door-Window Transmitter w/Reed Switch EN1215EOL Universal Transmitter with Wall Tamper & EOL Survey Transmitter EN1215WEOL Door‑window Transmitter w/ Wall Tamper, Reed Switch, & EOL EN1260 PIR Transmitter EN1262 PIR Transmitter EN1265 PIR Ceiling Motion EN1261HT PIR High-traffic EN1242 Smoke EN1247 Glassbreak EN1249 Billtrap ISW-TRL8080 EN7280 Receiver/Translator Kit EN4204R LED Receiver EN4216R LCD Receiver EN5040-T High‑power Repeater EN7016 Wireless Survey Kit EN1210SK Compatible Transmitters designated with ISW-ENxxxx part numbers: ISW-D8125CW-V2 Wireless Interface ISW-EN4200 Wireless receiver ISW-EN1223D Water‑resistant Pend Panic ISW-EN1223S Water‑resistant Pend Panic ISW-EN1233D Necklace Pendant Panic ISW-EN1233S Necklace Pendant Panic ISW-EN1235S Belt-clip Panic ISW-EN1235D Belt-clip Panic ISW-EN1235SF Fixed Location Panic ISW-EN1235DF Fixed Location Panic ISW-EN1210EOL Universal Transmitter w/ EOL ISW-EN1210W Door-Win Transmitter w/Reed Switch ISW-EN1215EOL Universal Transmitter with Wall Tamper & EOL ISW-EN1215WEOL Door‑window Transmitter w/ Wall Tamper, Reed Switch, & EOL ISW-EN1260 PIR Transmitter ISW-EN1262 PIR Transmitter ISW-EN1265 PIR Ceiling Motion ISW-EN1261HT PIR High-traffic ISW-EN1242 Smoke ISW-EN1247 Glassbreak ISW-EN1249Billtrap ISW-TRL8080 Translator ISW-EN7280 Receiver/Translator Kit ISW-EN4204R LED Receiver ISW-EN4216R LCD Receiver ISW-EN5040-T High‑power Repeater ISW-EN7016 Wireless Survey Kit ISW-EN1210SK Survey Transmitter
    View full article
    ‎08-06-2018 08:33 PM
    How to vew the History log on D7000/9000 and G series panels. D7212B,D7212B1,D9112,D9112B,D9112B1.
    View full article
    ‎06-12-2018 07:11 PM
    How to configure the Swinger Count and use Swinger Shunt.
    View full article
    ‎07-31-2018 10:22 PM
    Keypad programming is available in GV3 panels with firmware revision 8.10 or higher.  NOTE: Keypad programming is not available during while an RPS programming session is active, or when any area is armed. Enter from normal operation: Press [9]+[9]+[Enter]. Select Keypad Programming. The keypad displays Enter Passcode. Enter the service passcode (default= 123). Enter from service mode (reset pin closed): D1255: Set the address to 16 with dipswitch: 1-5= OFF and 6= ON. The keypad displays Enter Passcode when the reset pin is closed. Enter the service passcode (default= 123). D1260: Set the address to 8 with dipswitch: 1-3= OFF and 4-6= ON. The keypad displays Enter Passcode when the reset pin is closed. Enter the service passcode (default= 123). The following options are available upon entering keypad programming: Phone Numbers – Phone 1 thru Phone 4 Phone Format - Phone 1 thru Phone 4 Enhanced Comm – Path 1 thru 4 Routing Route Groups 1 thru 4 RPS Parameters RPS Passcode RPS Phone Number RPS IP Address RPS IP Port Area Parameter – 1 thru 32 Account On – Yes / No Account Number Command Center 1 thru 16 Enhanced Command Center – Yes / No Command Center Scope – User Pass Code User 0 (Install Passcode) User 1 (User Passcode) Point Parameters D9412GV3: 1-247 D7412GV3: 1-75 D7212GV3 1 -40 Point Index Disable Keypad Programming
    View full article
    ‎06-20-2018 03:05 PM
    How to program the panel to auto arm at the end of a closing window.
    View full article
    ‎05-14-2018 05:08 PM
    The panel will not send alarm reports and instead is sending an 'ALARM RECENT CLS’ event.
    View full article
    ‎05-15-2018 05:14 PM
    How to work around the D5360 is unable to access Remote Programming Software Diagnostics or Get History operation.
    View full article
    100% helpful (1/1)
    ‎06-27-2018 05:19 PM
    Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2, D8112A
    View full article
    0% helpful (0/1)
    ‎06-06-2018 10:47 PM
    How to convert Popit addresses from the D8112G2 to be used on a G-Series panel.
    View full article
    ‎08-02-2018 08:36 PM
    Issue How does the FIRE TEST COMMAND 58 feature function? Solution • Use this function to test fire points and other 24-hour points to be certain they function properly. You can review both the tested and untested points at your command center to help pinpoint any problems. • Upon initiation, the fire test will test the fire bell pattern on the bell output and ring the command center fire bell for 2 seconds. The AC will be disabled for 4 minutes in order to test the system’s battery power. If the battery cannot maintain the system for the 4 minute period, the command center will appear to go dead. If this happens, contact your security company. At the end of the 4 minute period, AC is returned to the system and the panel restores. A message will be sent to your security company upon initiation and completion of the Fire Test. During the Fire Test, no 24-hour alarms will be sent to your security company. • If there is no activity on the system for 20 minutes, the system will automatically exit from the Fire Test. Using COMMAND 58: 1. Ensure your command center is at disarmed idle text. 2. Press the COMMAND bar. The display shows SYSTEM COMMAND. 3. Press the 5 key, then press the 8 key. Note: If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function. Press the MENU key to enter the Command Menu, then press NEXT repeatedly until you reach the FIRE TEST ? prompt. Press ENT. 4. The display shows ## PTS TO TEST. 5. One-at-a-time, activate the detection devices to fault each point. 6. As you fault each point, your command center will display the point text for 60 seconds and ring the fire sounders for 2 seconds. This verifies that the detection device is working properly. Your system automatically resets smoke detectors. • When a resettable point (such as a smoke detector) is faulted, the display shows SENSOR RESETTING for 5 seconds. During this time power is removed from smoke power relays. • Faulting a point more than once does not increment the test count. However, the command center emits a brief tone and displays the point text each time you fault the point allowing you to test multiple devices assigned to one point. 7. When all 24-hour points have been tested, 0 PTS TO TEST is displayed. Press ESC. The display momentarily shows ALL PTS TESTED before returning to idle text. 8. During the Fire Test you may want to see the points that remain untested. When point text is displayed, press ESC. The display shows ## PTS TO TEST. Press the ESC key. VIEW UNTESTED ? is displayed. Press ENT. ## PTS UNTESTED is displayed. Press NEXT to see a list of the points that have not yet been tested. Move through this list by pressing the NEXT key. To resume the Fire Test, press ESC. ## PTS UNTESTED is displayed. Press ESC. ## PTS TO TEST is displayed. Resume testing points. To end the Fire Test, press ESC twice.
    View full article
    ‎06-11-2018 07:38 PM
    How to upgrade the D8112 and use existing Popit addresses and/or Popits.
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist