Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎06-15-2018 09:33 PM
    How to correct the D1260 error: Incorrect panel programming, enhanced should be set to yes.
    View full article
    ‎05-22-2018 03:42 PM
    How is the keypad's display brightness changed? DS7400XIVER3+,DS7447I
    View full article
    ‎07-02-2018 03:19 PM
    Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7447, DS7447E
    View full article
    ‎06-01-2018 04:01 PM
    The D4412 and D6412 use the D621, D623 or D625 command centers. Pressing All-On or Part-On on the will arm only the area where the keypad is assigned. Command 50 may be used to move to an area other than the programmed assigned area.  After moving to the selected area, press either All-on or Part-on to arm the area. Command 80 may be used to arm all areas. Command 81 may be used to disarm all areas. Note:  Commands 80 and/or 81 must be enabled by an individual with assigned authorization to perform the function. Use Command 50 to move to another area and arm:  Press [CMD] [5][0] and enter a valid code if required. The keypad will scroll through all available areas. Press the desired area number to move to the area.  Press All-On or Part-On to arm the selected area.  Pressing and holding [CMD] will exit the Command 50 feature returning the keypad to its “home” area. Use Command 80 to arm All Areas: Press [CMD] [8][0] and enter a valid code if required.       Hold down the All On key for 2 sec and it forces all areas to All On.  Use Command 81 to disarm All Areas:  Press [CMD] [8][1] and enter a valid code if required. The keypad will indicate all areas are off.
    View full article
    ‎06-18-2018 09:57 PM
    How to view System Troubles on the DS7240/DS7220. DS7240,DS7220,DS7445I,DS7447I
    View full article
    ‎05-25-2018 05:22 PM
    How to make Custom Text display after replacing the keypad. D2212, D2412, D2812,Custom Text, D223,D222, Remote Programming Software, D5200
    View full article
    ‎06-01-2018 09:53 PM
    How to configure the the GV3 v8.10+ for using a D1260 or D1265 with keypad programming.
    View full article
    ‎06-18-2018 07:17 PM
    Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G, D1260
    View full article
    ‎06-18-2018 06:47 PM
    How to view the panel log file using the DS7447 keypad. DS7400X,DS7400,DS7400Xi,DS7400XIVER3+,DS7400XIVER4+,DS7400XIVER2,DS7447I,DS7447E,DS7447
    View full article
    ‎06-19-2018 02:20 PM
    Can the D220A Keypad be used with a D2112? How to determine which resistor to cut from the D220A Keypad to work with a D2112 panel. D220A (8 led),D2112,D2412,D2812,D2212.
    View full article
    ‎05-25-2018 05:05 PM
    The to activate the A, B or C Key on a 2000 Series control panel.  D2212,D2412,D2812, A Key, B Key ,C Key, D223, D222, D5200
    View full article
    ‎07-02-2018 10:09 PM
    Issue What would cause the Armed LED to not function on an LED Command Center, while arming the system? Solution To correct the Armed LED try the following steps: 1. Recycle power to the command center, and the panel. 2. Readdress the command center, anything other than address one. Then reprogram the command center for the same address number, and reset the panel.
    View full article
    ‎05-23-2018 08:31 PM
    Why are the keypads not displaying proper text? D2212,D2412,D2812,D223,D222
    View full article
    ‎06-13-2018 07:26 PM
    How to correct custom functions that execute when A, B or C keys are pressed on the D720. D1256 Command Center functions are Executing when A, B or C Keys on a D720 are pressed.
    View full article
    ‎06-12-2018 10:43 PM
    How to correct when the Independent Zone Controller point never restores to normal. The panel point that uses a D279 or D279A never shows normal even though the Independent Zone Controller points are all normal. D279A,D279
    View full article
    ‎05-21-2018 08:14 PM
    How are passcodes changed using the keypad on a 2000 Series control panel? D2112, D2412, D2212
    View full article
    ‎06-25-2018 06:29 PM
    Issue Why is the green LED not lit on the 251 keypad?   Solution   The green LED monitors loop status, power supply, and the fuse on the panel. If the LED is shut off check all of the above. Note: zones are supervised with a 1K ohm resistor and 16.5VAC 20 VA transformer is used for AC power.
    View full article
    ‎06-18-2018 06:55 PM
    How to interpret a Battery Low report on the D4412/D6412. What battery voltage will the panel transmit a BATTERY LOW report?
    View full article
    ‎06-28-2018 04:29 PM
    How to troubleshoot why Zone Test will not work on a DS7400 Version1 or 2 Panel. DS7400,DS7400X,DS7400XIVER2.
    View full article
    ‎06-14-2018 06:58 PM
    Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G, D1255, D1255RB, D1255R, D1255W
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist