Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎09-20-2018 06:49 PM
    How to modify the B465 Network Access Point Name (APN) entry. What APN is used for the Verizon, AT&T, T-Mobile or Rogers network?
    View full article
    ‎09-11-2018 10:47 PM
    How to use the G Series Battery supervision and Discharge - Recharge Schedule.
    View full article
    ‎09-14-2018 04:34 PM
    Issue The keypad displays the Access Module Door Point is in trouble. Diagnostics displays the point as missing. Solution T+ (Tamper Input) of the Access Module is an unsupervised input that is normal when open. Upon a short, the Door Point number assigned to the supervised zone of the Access Module is reported as a MISSING PT###.
    View full article
    100% helpful (1/1)
    ‎09-14-2018 04:33 PM
    How to use the B Series panel Battery supervision and Discharge - Recharge Schedule.
    View full article
    ‎08-27-2018 07:06 PM
    How to work with the D6112 Battery Discharge and Recharge voltage schedule. When does the D6112 report Low Battery? When does the D6112 report Low Battery Restoral?
    View full article
    ‎08-27-2018 07:11 PM
    How to work with the D4112 Battery Discharge and Recharge voltage schedule. When does the D4112 send a Trouble Low Battery report to the monitoring station? When does the D4112 send the Low Battery restore report to the monitoring station?
    View full article
    ‎07-06-2018 08:10 PM
    Program network reporting in GV3 version 8.10 and higher control panels.
    View full article
    ‎06-01-2018 02:47 PM
    Bosch Security Knowledge Base Related Products D6600 D6200 D6640 D6641
    View full article
    100% helpful (1/1)
    ‎08-10-2018 09:56 PM
    B465 USB Menu Map
    View full article
    ‎08-10-2018 09:56 PM
    Primary Power Low or Missing B465
    View full article
    ‎08-06-2018 08:34 PM
    Issue What voltage and current is the phone line monitor measuring to sense trouble on the phone line on the D7212B/D9112B panels?   Solution   The phone line monitor senses trouble when the voltage on the line falls below 4.5 to 7.5 VDC, or in the off-hook condition when the current is 8 to 13mA.
    View full article
    ‎08-06-2018 08:33 PM
    How to vew the History log on D7000/9000 and G series panels. D7212B,D7212B1,D9112,D9112B,D9112B1.
    View full article
    ‎08-06-2018 08:32 PM
    Issue How is the history reset after an event overflow message?   Solution   Receive the panel's history, choose the set pointer option to have panel start history from that point forward on newer just receiver Current.   Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G
    View full article
    ‎08-02-2018 08:36 PM
    Issue Points are faulted but the panel does not react. Solution Points must be faulted for 500 milliseconds minimum. *When using self resetting devices, some do not latch the contact in the faulted position but do show a fault trip via a latched LED.
    View full article
    ‎08-02-2018 07:49 PM
    How to troubleshoot missing alarms on points connected to the D222A keypad. D2212, D2412, D2812, D222A.
    View full article
    ‎08-02-2018 08:36 PM
    Issue How does the FIRE TEST COMMAND 58 feature function? Solution • Use this function to test fire points and other 24-hour points to be certain they function properly. You can review both the tested and untested points at your command center to help pinpoint any problems. • Upon initiation, the fire test will test the fire bell pattern on the bell output and ring the command center fire bell for 2 seconds. The AC will be disabled for 4 minutes in order to test the system’s battery power. If the battery cannot maintain the system for the 4 minute period, the command center will appear to go dead. If this happens, contact your security company. At the end of the 4 minute period, AC is returned to the system and the panel restores. A message will be sent to your security company upon initiation and completion of the Fire Test. During the Fire Test, no 24-hour alarms will be sent to your security company. • If there is no activity on the system for 20 minutes, the system will automatically exit from the Fire Test. Using COMMAND 58: 1. Ensure your command center is at disarmed idle text. 2. Press the COMMAND bar. The display shows SYSTEM COMMAND. 3. Press the 5 key, then press the 8 key. Note: If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function. Press the MENU key to enter the Command Menu, then press NEXT repeatedly until you reach the FIRE TEST ? prompt. Press ENT. 4. The display shows ## PTS TO TEST. 5. One-at-a-time, activate the detection devices to fault each point. 6. As you fault each point, your command center will display the point text for 60 seconds and ring the fire sounders for 2 seconds. This verifies that the detection device is working properly. Your system automatically resets smoke detectors. • When a resettable point (such as a smoke detector) is faulted, the display shows SENSOR RESETTING for 5 seconds. During this time power is removed from smoke power relays. • Faulting a point more than once does not increment the test count. However, the command center emits a brief tone and displays the point text each time you fault the point allowing you to test multiple devices assigned to one point. 7. When all 24-hour points have been tested, 0 PTS TO TEST is displayed. Press ESC. The display momentarily shows ALL PTS TESTED before returning to idle text. 8. During the Fire Test you may want to see the points that remain untested. When point text is displayed, press ESC. The display shows ## PTS TO TEST. Press the ESC key. VIEW UNTESTED ? is displayed. Press ENT. ## PTS UNTESTED is displayed. Press NEXT to see a list of the points that have not yet been tested. Move through this list by pressing the NEXT key. To resume the Fire Test, press ESC. ## PTS UNTESTED is displayed. Press ESC. ## PTS TO TEST is displayed. Resume testing points. To end the Fire Test, press ESC twice.
    View full article
    ‎08-02-2018 08:35 PM
    Issue When using 4 wire smoke detectors on the D6112, where do the detectors power connections need to be landed on the panel to provide reset capabilities with Command 47?   Solution   The power connections need to be landed on terminal 15(+) and 14(-) for the reset to occur when a CMD 47 is entered at the keypad.
    View full article
    ‎08-02-2018 08:35 PM
    Part Numbers D222, D222A, D223, D223A, D2212, D2212B, D2212BE, D2412, D2812, D2412U, D2412UE, D2812U, D2812P
    View full article
    ‎08-02-2018 08:35 PM
    Issue The D8112 panel is not sending signals when modem format is selected to the Central Station. Solution Only the D8112G2 can send signals in Modem II format with a CS setting of 7. The D8112E, D8112E1, D8112G, D8112G1 and D8112A must have CS set to either Blank or a selection between 1 and 6 but not 7. Only Modem Format can report a 4 digit account number to the Central Station all others only report a 3 digit account number.
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist