Security: Video

In certain situations of the support process for a particular product, the customer number and the material/ serial/ commercial type number of your Bosch device may be required. But where can you find them? The purpose of this article is to help you find this information in different ways.

Various overlays in the video image provide important status information. But what does mean the blinking play button near the yellow exclamation icon?

Question: If your VIDEOJET decoder does not seem to work properly ,   most likely it is because the software (SW) version used is not compatible with the firmware (FW) version of your device. But which are the system requirements for configuration/ operation purposes of VIDEOJET decoder 3000/ 7000/ 8000?

This article aims to define the way you can display camera video via decoders. Moreover, fifteen different settings scenarios and their effects will be outlined for the live video to be displayed through the decoder. Article requirements: BVMS Camera Decoder

Which Bosch encoders and decoders are compatible with BVMS? Up until some years ago, new released cameras, encoders, domes and decoders that are introduced into market after a BVMS release could not be connected to an existing BVMS version because these cameras where not known to the BVMS. In the BVMS 4.5.1, a new concept was introduced. This concept treats Bosch video encoders and decoders as generic devices, and automatically recognizes specific device functionality (for example the number of streams, relays and inputs). Based on this information the, at that time, unknown device is added to the system and can be used by the operator. The attached document provides a detailed description of this functionality.

rectrieve live video with Video Security Client Software for Windows version 2.2

MTU and MSS     MTU stands for "Maximum Transmission Unit." MTU is a networking term that defines the largest packet size that can be sent over a network connection. The MTU is typically limited by the type of connection, but may sometimes be adjusted IT network settings. The typical value of the Network MTU is 1514 Byte. If a system sends packets over an Ethernet network that are larger than this size, the data will be fragmented into smaller packets. When referring to Ethernet MTU this includes 4 Byte checksum. The  1514 Byte is the interface MTU without the Ethernet Checksum. In cae there are limitations by the type of connection, the packets will then need to be reassembled on the receiving side (e.g. Bosch video management software or Bosch hardware decoder). However, it can be beneficial to optimize the packet size on the sender side (e.g. IP camera) to the exisitng network infrastructure. As MTU maximum packet size is layer 1 related, the IP MTU that you can be adjusted at the BOSCH device configuration (Configuration Webpages or with the help fo BOSCH configuraiton software like "Configuraiton Manager"). The BOSCH GUI refers to this as “Network MTU”. BOSCH products can manage fragmented data. MSS stands for "Maximum Segment Size" The MSS value is calculated from the MTU. MSS = MTU – (layer 3 TCP header [20 Byte] + Layer 2 IP header [20 Byte]+ Layer Ethernet 1 [6+6+2 = 14 Byte]) For example looking at CPP 6 Platform – like FLEXIDOME IP panoramic 7000 MP in Firmware version 6.50.0128 you can adjust and find the following values: Network MSS (in Byte) - default value = 1460 iSCSI MSS (in Byte) – default = 1460 Network MTU (in Byte) – default = 1514   MTU and MSS can be adjusted at all released firmware versions 4.x and later. CPP-ENC CPP3 CPP4 CPP5 CPP6 CPP7 CPP7.3 yes x x x x x x x No               Here some screenshots as example based on Firmware 06.50.0128  

 This article describes how to collect log files and configuration of IP cameras, encoders and decoders. 

Related Products - VJD-3000 Question How to display MPEG 4 video on VIDEOJET decoder 3000 ? Answer No. VIDEOJET decoder 3000 is only capable of decoding H.264 video.

Related Products VIPXD (Audio Version)   Question Why there is NO sound from a loudspeaker connected to a VIPXD SPK port?   Answer The RTC_AUDIO_LOUDSPEAKER_ON_OFF flag is not activated. This flag can be set manually by using this CGI command: http://160.10.x.x/rcp.xml?command=0x09be&type=F_FLAG&payload=1&direction=WRITE&num=1 Replace 160.10.x.x by your VIPXD IP address.