The disks in an array are usually configured into smaller sets named RAID groups which provide protection against failure.
The RAID groups define the manner in which the group of physical disks handle data when it is written to the disks within that group. The main aim is that data to be protected.
For this reason, you must create logical unit numbers (LUNs) correctly.
This article describes all the steps that will help you to create LUNs after RAID failure.
Bosch has been providing 2 types of VRM packages: a 32bit and a 64bit version. Since VRM 3.82 we are only offering the 64bit version.
As all of our released DIVAP IP units started off as 32bit VRM which includes a Transcoder service.
If you do not use the Start.exe included in the VRM Master Installer, you will not be offered the oppertunity to also upgarde the Transcoder. Just running the Setup_VRM_Service_<version>.exe found in the <Install\Bosch> folder, will cause the Transcoder service to stop functioning!
This includes if the upgarde is done via BVMS installer.
Since BVMS 10.0, VRM 3.82 "64bit" was implemented.
Due to the fact that BVMS does not manage the transcoder, it was not installed.
Also see Firewall settings: HowTo Configure Windows Firewall Rules, includes PS script to adjust the VRM 64bit and Transcoder rules.
Download the appropriate VRM version from our Downloadstore
Run the Start.exe
Deselect all components and choose only the Transcoder Service
Click on "Install"
To confirm that the Transcoder is fully functional, open your browser and navigate to the VRM Monitor:
Log in with you Credentials
Possible Communication Issue between BVMS 8.0 Central Server and Video Recording Manager (VRM) 3.7x with BVMS 8.0 installed on different Servers.
Communication can get interrupted and configuraiton might fail if the below desribed actions are not performed. If your system is affected or not is described here as follows:
There can be authentication issues between the BVMS Central Server and the Video Recording Manager in case they are installed on different Servers.
It is possible to see reports at the BVMS 8.x system alarms that VRM reports wrong version
Please check in the VRM debug logging if the following logline indications can be found
CONFIG;DEBUG;SENDING XPATH /SYSTEM/DEVICES/DEVICE as well as HAS NO CONFIGURED NODE, SET TO CONFIGURED
CONFIG;INTERNAL;/SYSTEM/DEVICES CHANGED IN CONFIG. DEVICEID= [DEVICE IP]\0;SYSINFO;INTERNAL;LINE 1 HAS NO CONFIGURED NODE, SET TO CONFIGURED
In general please keep in mind, that it is strongly recommended to use VRM 3.71.00xx with BVMS 8.0. Do not use any older VRM version like 03.71.0022. The 03.71.0029 and Releaseletter is available at the BOSCH DownloadStore (status update 2018-10-26). https://downloadstore.boschsecurity.com/FILES/Setup_VRM_03.71.0029_win32.zip Release Letter: https://downloadstore.boschsecurity.com/FILES/Bosch_Releaseletter_VRM_3.71.0029.pdf
At the VRM system / server, please check and ensure that the following Microsoft software packages are pre-installed:
.NET framework 4.6.2 or higher
Redistributables for Visual Studio 2015
In case one component is missing, please perform the following steps:
Download the missing Microsoft components. Note: When using BVMS 8.0 the VRM is typically a 32-Bit VRM software. Therefore the 32-Bit Microsoft packages are needed. Component that was seen as missing is the >> “Visual C++ Redistributable for Visual Studio 2015” https://www.microsoft.com/en-US/download/details.aspx?id=4814 Please choose the 32-Bit version of that when using with 32-Bit VRM and the >> .NET framework 4.6.2 or higher (NDP462-KB3151800-x86-x64-AllOS-ENU.exe) https://www.microsoft.com/en-US/download/details.aspx?id=53344
Stop the VRM (rms.exe) service in Windows services
Install those components with Administrator rights at the VRM server Reboot the server after installation of the Microsoft components
Check if the VRM service is running and if needed Re-Start the VRM (rms.exe) service
Check that the combination of messages are not longer seen in the VRM debug logging
The VRM package is enhanced and useres should no longer run into this issue with VRM 3.81 and newer versions. Please be aware that BVMS releases are tested with certain VRM verions. This still can offer to install a newer VRM than originally rolled-out in the BVMS overall installer. For all VRM versions 3.7x and below 3.81 it is needed to add this packages.