This troubleshooting guide, will guide you through the recovery steps of an DIP, without video data loss
General note: Using a Bosch DIP system without video data disks is a non supported use case, its mandatory to equip the system with data disks to recover the system.
Step 1 - Preperation
Download the attachment repair.zip and unzip the content
Prepare an USB-stick, rename it to SCRIPT
Copy the repair.txt extracted of the attachment on the USB-stick
Insert the USB-stick into an USB-slot of your machine
Insert the BOSCH r ecovery DVD into the DVD-drive
Step 2 - Create RAiD1
Boot the machine and enter the Intel RAiD MENU pressing CTRL + I
Navigate to CREATE RAiD VOLUME and hit enter
Set RAiD level to RAiD1(Mirror), navigate to CREATE VOLUME and hit enter
Exit the RAiD controller, navigate to EXIT and hit enter
Reboot the machine (e.g. press CTRL + ALT + DEL)
Step 3 - System Recovery
During the reboot, boot from DVD, press ENTER as the line will displayed
In the System Management Utility, click on CONSOLE
Type into command line "diskpart.exe" hit enter
Type into command line "list volume" hit enter and search for your USB-stick called SCRIPT, note down the assigned drive letter (LTR)
End diskpart.exe by typing on the command line "exit" hit enter
Type into the command line "diskpart.exe /s [YOUR_USB_DRIVE_LETTER]:\repair.txt" hit enter
Wait until the script has been finished and CLOSE the console
Step 4 - System Recovery
On the System Management Utililty click on SYSTEM RECOVERY (back to factory default)
NOTE: Do not select Initial Factory Setup, this will wipe all existing data!
As the recovery has been completed, click on OK to confirm and reboot
Do not eject the DVD and follow the instructions on your screen to initialize the system.
Possible Communication Issue between BVMS 8.0 Central Server and Video Recording Manager (VRM) 3.7x with BVMS 8.0 installed on different Servers.
Communication can get interrupted and configuraiton might fail if the below desribed actions are not performed. If your system is affected or not is described here as follows:
There can be authentication issues between the BVMS Central Server and the Video Recording Manager in case they are installed on different Servers.
It is possible to see reports at the BVMS 8.x system alarms that VRM reports wrong version
Please check in the VRM debug logging if the following logline indications can be found
CONFIG;DEBUG;SENDING XPATH /SYSTEM/DEVICES/DEVICE as well as HAS NO CONFIGURED NODE, SET TO CONFIGURED
CONFIG;INTERNAL;/SYSTEM/DEVICES CHANGED IN CONFIG. DEVICEID= [DEVICE IP]\0;SYSINFO;INTERNAL;LINE 1 HAS NO CONFIGURED NODE, SET TO CONFIGURED
In general please keep in mind, that it is strongly recommended to use VRM 3.71.00xx with BVMS 8.0. Do not use any older VRM version like 03.71.0022. The 03.71.0029 and Releaseletter is available at the BOSCH DownloadStore (status update 2018-10-26). https://downloadstore.boschsecurity.com/FILES/Setup_VRM_03.71.0029_win32.zip Release Letter: https://downloadstore.boschsecurity.com/FILES/Bosch_Releaseletter_VRM_3.71.0029.pdf
At the VRM system / server, please check and ensure that the following Microsoft software packages are pre-installed:
.NET framework 4.6.2 or higher
Redistributables for Visual Studio 2015
In case one component is missing, please perform the following steps:
Download the missing Microsoft components. Note: When using BVMS 8.0 the VRM is typically a 32-Bit VRM software. Therefore the 32-Bit Microsoft packages are needed. Component that was seen as missing is the >> “Visual C++ Redistributable for Visual Studio 2015” https://www.microsoft.com/en-US/download/details.aspx?id=4814 Please choose the 32-Bit version of that when using with 32-Bit VRM and the >> .NET framework 4.6.2 or higher (NDP462-KB3151800-x86-x64-AllOS-ENU.exe) https://www.microsoft.com/en-US/download/details.aspx?id=53344
Stop the VRM (rms.exe) service in Windows services
Install those components with Administrator rights at the VRM server Reboot the server after installation of the Microsoft components
Check if the VRM service is running and if needed Re-Start the VRM (rms.exe) service
Check that the combination of messages are not longer seen in the VRM debug logging
The VRM package is enhanced and useres should no longer run into this issue with VRM 3.81 and newer versions. Please be aware that BVMS releases are tested with certain VRM verions. This still can offer to install a newer VRM than originally rolled-out in the BVMS overall installer. For all VRM versions 3.7x and below 3.81 it is needed to add this packages.