Bosch Building Technologies

    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Video

    Sort by:
    ‎04-04-2019 09:19 AM
    Symptoms transparant data transmission at a Encoder VideoJet Multi 4000 or VIP-X16-XF-E stops / does not work any longer in case of a power outage and restart of the device. Diagnosis when e.g. controlling a Bosch Autodome 7000 and PTZ via Transparent Data not working after reboot of the encoder, this is caused by an issue in the released firmware. It doesn't matter if it is Firmware 6.30.0047 or 6.30.0059. As a power outage should happen not too often the solution below is offered to fix this. Solution The solution is via a workaround using an ATSL script in the encoder to re-set the COM port baud-rate upon a reboot/restart of the encoder (which should in normal practice not happen to often). Please add th following scritp to the Alarm Task Editor tab either via CM or Web interface. //The 1st line set the board rate, 2nd line sets the port type RS232 = 1 or RS485/422 = 2 RcpCommand setCOMBaudrate := { Command( "rcp.xml?command=0x027e&type=T_DWORD&direction=WRITE&protocol=TCP&payload=9600&num=1" ) }; RcpCommand setCOMMode := {Command("rcp.xml?command=0x0208&type=T_OCTET&direction=WRITE&protocol=TCP&num=1&payload=2")}; if (true) then setCOMBaudrate, setCOMMode; If the device has a password set then 2 additional perimeters need to be added UserName() and Password(""). RcpCommand <name of RCP command> := { Command( "Bla Bal Bla" ) UserName(Service) Password( "enter the service level password here" ) }; There will be no furhter release or fix provided by BOSCH status of 2019-03-19 as the ATSL script resolves this.
    View full article
    ‎06-18-2018 09:56 AM
     This article describes how to collect log files and configuration of IP cameras, encoders and decoders. 
    View full article
    ‎05-21-2018 08:40 PM
    This will let you call up cameras on an Allegiant monitor output across the network to a remote site.
    View full article
    ‎05-21-2018 08:33 PM
    Connections and programming for VIP X1XF and VG5 600 Dome.
    View full article
    100% helpful (1/1)
    ‎05-18-2018 01:41 PM
    Related Products All IP encoders   Answer Copy/Paste this example into the alarm task editor and save.  See comments below for more details, annotated by //. // Settings for JPEG posting JpegPosting PicPosting := { IP( "put ftp FQDN servername or IP here" ) Login( "anonymous" ) Password( "anonymous" ) Format( Large ) FileName( "Snap" ) Suffix( Date ) Camera( All ) }; // Define Operation Mode to periodic, 15min low and 0.1 second high OperationMode periodic := { Low(18000) High(1) }; //define logic TempState(1):=periodic; if(true) then TempState(1); if (TempState(1)) then PicPosting;
    View full article
    ‎05-18-2018 01:39 PM
    Related Products Bosch encoders Answer Place this in the alarm task editor and save it.  Please read the comments for more details.  They are noted below by //. //Define weekly timer from Monday to Sunday from 7am to 9pm Timer weekly := {TimeBegin(07:00) TimeEnd(21:00) DayBegin(Mo) DayEnd(Su) }; //define what is to be recorded Recording recording:= { Camera(All) }; // Define Operation Mode to periodic, 1 sec low 30 min high OperationMode periodic := { Low(10) High(18000) }; TempState(1):=periodic; //define recording timer OperationMode monostable := {High(50)}; TempState(2):=monostable; //Turn on recording timer if (IsActivated(weekly)) then TempState(1) := true; if (TempState(1)) then TempState(2) := true; if (TempState(2)) then recording else Stop(recording);
    View full article
    ‎05-18-2018 01:23 PM
    How many streams can use the BP+ profile?
    View full article
    ‎05-16-2018 09:24 PM
    Related Products Bosch Recording Station Video Jet X Series BRS   Question Is it possible to control an AutoDome connected to VideoJet X Series via Bilinx?   Answer In BRS 8.8.1 Bilinx over Encoder only works for devices connected via VSDKPluginModule. Current supported devices are VIP-X1600-XFM4B and VIP-X1XF. VideoJet X series are connected per default via VCSModule, which does not support Bilinx communication. To be able to control Bilinx devices on VideoJet X series please configure the following work around: 1. In BRS Configuration > IP Cameras and encoders > Scan network (VideoJetX is found) and add VideoJetX device to BRS 2. Click VideoJetX and click Edit 3. In tab General settings select Device Type BVIP H.264 4. In tab Dome settings mark Activate and select Connection Bilinx/IP Dome Now the AutoDome can be controlled via Bilinx. Note: Due to performance reasons do not change the encoder stream from MPEG-4 SH++ to H.264 streaming! Only change the device type in BRS.
    View full article
    Top Contributors