Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Video

    Sort by:
    ‎08-09-2021 04:02 PM
    The Bosch VRM Monitor page does not open correctly, but instead displays an Error. Any Replay client requesting video from the  Bosch Video Recording Manager service, only receives the Time-Line but the video is alway Black. Bosch VRM by default uses Ports 80 & 443.
    View full article
    ‎05-21-2018 08:36 PM
    Related Products Bosch Recording Station (BRS) version 8.9 and later   Question I cannot configure UDP tunneling on BRS. Network cards are grayed out.   Answer Under certain circumstances BRS NetLimiter may become not registered. The network cards are not shown in Configuration > Security and Network > Network settings. In that case, register BRS NetLimiter manually: 1. Close BRS application 2. Control Panel > System and Security > Administrative Tools > Services > Bosch Networking Service    a) Set "Startup Type" to "disabled"    b) Stop service    c) In a console window with administrative rights, enter "C:\Program Files\Bosch\Recording Station\NetLimiterServer" /service    d) Set "Startup Type" to "Automatic"    e) Start service 3. Start BRS application
    View full article
    ‎05-21-2018 08:30 PM
    Related Products DVR 700 series BVIP device   Question Why does Divar 700 change the settings of 2nd stream, even though only 1st stream is configured in the DVR?   Answer Divar 700 uses the concept where it assumes to be the (master) device to have control over the cameras and their streams. Stream 1 is always set to profile 1 Stream 2 is always set to profile 2 Only one command is sent from DVR to set both stream 1&2 So please configure profile 2 in the wanted way to be used with stream 2.
    View full article
    ‎05-21-2018 08:30 PM
    Related Products VIPXD (Audio Version)   Question Why there is NO sound from a loudspeaker connected to a VIPXD SPK port?   Answer The RTC_AUDIO_LOUDSPEAKER_ON_OFF flag is not activated. This flag can be set manually by using this CGI command: http://160.10.x.x/rcp.xml?command=0x09be&type=F_FLAG&payload=1&direction=WRITE&num=1 Replace 160.10.x.x by your VIPXD IP address.
    View full article
    ‎05-18-2018 07:48 PM
    Related Products Bosch Video Client (BVC) Question Where can I find my stored recordings?   Answer Default path of the recordings is set as: C:\Documents and Setting\Admin\My Documents\Bosch\Video Client\Recordings This path can be changed in the configuration manager under the tab System > Applications > Video Client > Application > Manual Recording
    View full article
    ‎05-18-2018 01:23 PM
    How many streams can use the BP+ profile?
    View full article
    ‎05-18-2018 10:53 AM
    Restrictions of VRM Configuration utility pre-installed on DLA
    View full article
    ‎05-16-2018 09:24 PM
    Related Products Bosch Recording Station Video Jet X Series BRS   Question Is it possible to control an AutoDome connected to VideoJet X Series via Bilinx?   Answer In BRS 8.8.1 Bilinx over Encoder only works for devices connected via VSDKPluginModule. Current supported devices are VIP-X1600-XFM4B and VIP-X1XF. VideoJet X series are connected per default via VCSModule, which does not support Bilinx communication. To be able to control Bilinx devices on VideoJet X series please configure the following work around: 1. In BRS Configuration > IP Cameras and encoders > Scan network (VideoJetX is found) and add VideoJetX device to BRS 2. Click VideoJetX and click Edit 3. In tab General settings select Device Type BVIP H.264 4. In tab Dome settings mark Activate and select Connection Bilinx/IP Dome Now the AutoDome can be controlled via Bilinx. Note: Due to performance reasons do not change the encoder stream from MPEG-4 SH++ to H.264 streaming! Only change the device type in BRS.
    View full article
    ‎05-16-2018 09:41 AM
    Bosch ST has sold the HP Workstations and the HP Enterprise Servers  and is responsible to provide the required Service & Support for these products regardless of the SLA in place with HP. Therefore, the customer always will contact the Bosch After Sales organization in case of any problems encountered with one of these products. The customer must never been told to contact HP or HPE directly if he seeks support from Bosch. In this solution article a questionnaire for a first basic analysis of a reported issue is described. This checklist is intended to help to identify and resolve known issues immediately and to collect relevant data in case of an unknown issue.  
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist