Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Video

    Sort by:
    100% helpful (2/2)
    ‎09-11-2020 09:25 AM
    Related Products Bosch Video Client Question How do I backup the complete BVC configuration in Windows 7? Answer If BVC was installed whilst logged into Windows as the Administrator, go to the following folder: C:\Users\Administrator\AppData\Roaming\Bosch\Vidos. Copy the conf folder. This folder contains the BVC configuration. Note : Backup  configuration only applicable to the specific BVC version during configuration restore.
    View full article
    100% helpful (1/1)
    ‎03-18-2019 11:22 AM
    Related Products: Video Analytics for Firmware 6.60 and above This article covers traffic monitoring of Bosch Video Analytics with How to Videos (one already available and one in planning) Default scenario of wrong way detection Learn how to use the default scenario of wrong way detection: A predefined scenario that can be used to detect an object that is traveling the wrong way.   Default scenario traffic incidents This predefined scenario is designed to detect common traffic incidents on roads: Wrong way – triggers an alarm if object travels in wrong direction Pedestrian – triggers an alarm if pedestrian is on the road Slow vehicle – triggers an alarm if vehicle moves slower then predefined speed. Stopped vehicle – triggers an alarm when vehicle is stopped longer than predefined time span. Dropped object – Triggers and alarm if an object is dropped on the road   This how to video shows in detail how to use the predefined tasks Wrong way, Slow vehicle and Stopped vehicle.   Note: If needed you can get additional how to information on camera calibration.  
    View full article
    100% helpful (2/2)
    ‎04-09-2020 09:22 PM
    What are the best practices for surge and lightning suppression?
    View full article
    100% helpful (1/1)
    ‎05-10-2018 03:49 PM
    In rare situations it might happen that the mirrored SSD drives used for the Operating system need to be set-up from scratch when not only one, but both SSD drives used in the RAID-1 mirrored setup need to be exchanged with two new drives (e.g. Both SSD have been removed or were missing during first install attempt or imaging process from the recovery DVD. It is strongly recommended to always open a Technical Support Case at the local BOSCH Security Systems Level 1 Support team / help desk. Report the the following details to the support: Is the system registered at BOSCH? What is the System Serial-No.? What is the storage capcity of the new inserted two SSD drives at the rear side of the used DIVAR IP 70000 R2 system?
    View full article
    100% helpful (1/1)
    ‎05-13-2020 11:22 AM
    The attached technical notes give a short introduction to scripting alarm and counter tasks with Intelligent and Essential Video Analytics in FW 7.60. It also provides a broad selection of example scripts for explanation as well as including real world application examples.
    View full article
    100% helpful (2/2)
    ‎09-10-2018 01:43 PM
    Use the project assistant to commission multi-camera projects and generate project reports. Available for Windows and iOS and Android. (status 2018-08-06 / Version 1.1)
    View full article
    100% helpful (1/1)
    ‎05-18-2018 01:41 PM
    Related Products All IP encoders   Answer Copy/Paste this example into the alarm task editor and save.  See comments below for more details, annotated by //. // Settings for JPEG posting JpegPosting PicPosting := { IP( "put ftp FQDN servername or IP here" ) Login( "anonymous" ) Password( "anonymous" ) Format( Large ) FileName( "Snap" ) Suffix( Date ) Camera( All ) }; // Define Operation Mode to periodic, 15min low and 0.1 second high OperationMode periodic := { Low(18000) High(1) }; //define logic TempState(1):=periodic; if(true) then TempState(1); if (TempState(1)) then PicPosting;
    View full article
    100% helpful (1/1)
    ‎05-18-2018 01:49 PM
    Related Products All IP encoders Answer Copy/Paste the selection below to your alarm task editor and save. This script will make your encoder trip relay 1 only when IVA rule #1 alarm is active. // Set TempState to monostable mode, 5 seconds OperationMode monostable := { High(50) }; TempState(1) := monostable; if (VCARule(1,1)) then TempState(1) :=true; if (TempState(1)) then Relay(1) :=true else Relay(1) :=false;
    View full article
    100% helpful (1/1)
    ‎05-18-2018 02:03 PM
    Related Products All Bosch encoders running firmware 4.0 and above Question How can I set, clear and check virtual alarms via CGI? Answer  You can use virtual alarms within encoders as a trigger to have other events take place. This is an example on how to integrate 3rd party devices/software to trigger an event to take place on the encoder.  This event could be used to change any variable via ATSL (Alarm Task Script Language) - example below Virtual Alarms via CGI Set Virtual Alarm: http://160.10.92.40/rcp.xml?command=0x0a8b&type=F_FLAG&direction=WRITE&payload=01&num=1 Clear virtual Alarm: http://160.10.92.40/rcp.xml?command=0x0a8b&type=F_FLAG&direction=WRITE&payload=00&num=1 Check virtual Alarm: http://160.10.92.40/rcp.xml?command=0x0a8b&type=F_FLAG&direction=READ&num=1 Virtual Alarms in ATSL if (VirtualAlarm(1)) then Relay(1) := true; if (!VirtualAlarm(1)) then Relay(1) := false;
    View full article
    ‎09-03-2019 01:41 PM
    Dear users, have you ever wondered how to best transition from the Project Assistant to (B)VMS? This article aims at providing you a recommendation and the answer is quite simple: Use the Project Assistant to its full extent and once the cameras are connected to the target network, perform a network scan using the BVMS Configuration Client, to add the respective cameras to the system. The remaining fine-grained settings can then be tackled within BVMS.  For details, please check out the attached presentation. Let us know, if you have further questions and share your comments below. Best regards, Your Bosch Security App Team    
    View full article
    ‎05-16-2018 09:22 PM
    Related Products DHR 700 series DNR 700 series H.264 SD IP cameras   Question How can I record SD H.264 cameras in Main Profile (MP)?   Answer For the IP cameras disable the setting "SD display on local monitor required" - then the camera is disabled for live viewing but it is recorded in MP and can been seen via the BVC.
    View full article
    ‎05-14-2018 06:27 PM
    This article guides you through the process of activating Bosch VMS Audio Intercom functionality on Windows 7.
    View full article
    ‎05-16-2018 09:36 PM
    Related Products Bosch Video Management System   Issue When opening a new Image pane in Live Mode, the camera image is discolored, i.e. there is a green cast or the image is displayed in black and white. When viewing the same camera image with the webbrowser, the live image is properly colored.   Solution Update the graphics card driver. Refer to BVMS release notes: they list the recommended graphics card driver versions to be used. 
    View full article
    ‎05-21-2018 08:16 PM
    Related Products VRM Question Can I import Direct-to-iSCSI recordings into VRM? Answer No. iSCSI arrays used in Direct-to-iSCSI recording mode must be formatted when imported into VRM.
    View full article
    ‎05-21-2018 08:31 PM
    Related Products DiBos version 8.0 to 8.7 BRS version 8.8 and later   Question How to configure LDAP in DiBos / BRS?   Answer See attached 8 screenshots which guide through the LDAP configuration. Known restrictions on the AD: - users and user groups must be located in the same directory in the AD - DiBos / BRS supports max. 1000 user groups in the AD - Comma separated user (ex. User, John) are not supported.
    View full article
    ‎05-21-2018 08:33 PM
    Connections and programming for VIP X1XF and VG5 600 Dome.
    View full article
    ‎05-21-2018 08:39 PM
    This article guides you through the process of installing the BVMS Logbook Health Checker. The Bosch VMS Logbook Health Checker is a tool that is capable of fixing the overflow of the Bosch VMS Logbook database before it occurs.
    View full article
    ‎05-21-2018 08:40 PM
    This will let you call up cameras on an Allegiant monitor output across the network to a remote site.
    View full article
    ‎05-21-2018 08:42 PM
    In Bosch VMS it is possible to assign an LDAP user group to a Bosch VMS user group. This article describes why it is important to not assign the same LDAP user group to multiple Bosch VMS user groups.
    View full article
    ‎05-21-2018 08:46 PM
    Related Products - VJD-3000 Question How to display MPEG 4 video on VIDEOJET decoder 3000 ? Answer No. VIDEOJET decoder 3000 is only capable of decoding H.264 video.
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist