Related Products Bosch Video Client Question How do I backup the complete BVC configuration in Windows 7? Answer If BVC was installed whilst logged into Windows as the Administrator, go to the following folder: C:\Users\Administrator\AppData\Roaming\Bosch\Vidos. Copy the conf folder. This folder contains the BVC configuration.
Related Products: Video Analytics for Firmware 6.60 and above
This article covers traffic monitoring of Bosch Video Analytics with How to Videos (one already available and one in planning)
Default scenario of wrong way detection
Learn how to use the default scenario of wrong way detection: A predefined scenario that can be used to detect an object that is traveling the wrong way.
Default scenario traffic incidents
This predefined scenario is designed to detect common traffic incidents on roads:
Wrong way – triggers an alarm if object travels in wrong direction
Pedestrian – triggers an alarm if pedestrian is on the road
Slow vehicle – triggers an alarm if vehicle moves slower then predefined speed.
Stopped vehicle – triggers an alarm when vehicle is stopped longer than predefined time span.
Dropped object – Triggers and alarm if an object is dropped on the road
This how to video shows in detail how to use the predefined tasks Wrong way, Slow vehicle and Stopped vehicle.
Note: If needed you can get additional how to information on camera calibration.
In rare situations it might happen that the mirrored SSD drives used for the Operating system need to be set-up from scratch when not only one, but both SSD drives used in the RAID-1 mirrored setup need to be exchanged with two new drives (e.g. Both SSD have been removed or were missing during first install attempt or imaging process from the recovery DVD. It is strongly recommended to always open a Technical Support Case at the local BOSCH Security Systems Level 1 Support team / help desk. Report the the following details to the support: Is the system registered at BOSCH? What is the System Serial-No.? What is the storage capcity of the new inserted two SSD drives at the rear side of the used DIVAR IP 70000 R2 system?
The attached technical notes give a short introduction to scripting alarm and counter tasks with Intelligent and Essential Video Analytics in FW 7.60. It also provides a broad selection of example scripts for explanation as well as including real world application examples.
have you ever wondered how to best transition from the Project Assistant to (B)VMS?
This article aims at providing you a recommendation and the answer is quite simple: Use the Project Assistant to its full extent and once the cameras are connected to the target network, perform a network scan using the BVMS Configuration Client, to add the respective cameras to the system. The remaining fine-grained settings can then be tackled within BVMS.
For details, please check out the attached presentation.
Let us know, if you have further questions and share your comments below.
Your Bosch Security App Team
Related Products DHR 700 series DNR 700 series H.264 SD IP cameras Question How can I record SD H.264 cameras in Main Profile (MP)? Answer For the IP cameras disable the setting "SD display on local monitor required" - then the camera is disabled for live viewing but it is recorded in MP and can been seen via the BVC.
Related Products Bosch Video Management System Issue When opening a new Image pane in Live Mode, the camera image is discolored, i.e. there is a green cast or the image is displayed in black and white. When viewing the same camera image with the webbrowser, the live image is properly colored. Solution Update the graphics card driver. Refer to BVMS release notes: they list the recommended graphics card driver versions to be used.
Related Products DiBos version 8.0 to 8.7 BRS version 8.8 and later Question How to configure LDAP in DiBos / BRS? Answer See attached 8 screenshots which guide through the LDAP configuration. Known restrictions on the AD: - users and user groups must be located in the same directory in the AD - DiBos / BRS supports max. 1000 user groups in the AD - Comma separated user (ex. User, John) are not supported.
This article guides you through the process of installing the BVMS Logbook Health Checker. The Bosch VMS Logbook Health Checker is a tool that is capable of fixing the overflow of the Bosch VMS Logbook database before it occurs.
Upcoming with FW 7.10 and CM 6.20, Camera Trainer is a licensable Intelligent Video Analytics module that allows uses to define objects of intereste and train their own detectors for them based on examples of target objects and non-target objects. In contrast to the moving objects detected in general by IVA 7.10, Camera Trainer allows detection of both moving and non-moving objects, separates and immediately classifies them. Training can be done both on live video as well as on recordings available through the respective camera. The resulting detectors can be down- and uploaded for distribution to other cameras.
The attached fact sheet lists the cameras that support Camera Trainer. The attached technical note describes in-depth what Camera Trainer is, how it works, what to use it for and what not, and how to configure it. The configuration is also shown in the following how-to videos: Setup Camera Trainer Camera learning phase with recorded video
Configure Camera Trainer Task
Backup Camera Trainer Configuration - Method 1
Backup Camera Trainer Configuration - Method 2 Setup VCA Masking