This article aims to define the way you can display camera video via decoders. Moreover, fifteen different settings scenarios and their effects will be outlined for the live video to be displayed through the decoder.
In certain situations of the support process for a particular product, the customer number and the material/ serial/ commercial type number of your Bosch device may be required.
But where can you find them?
The purpose of this article is to help you find this information in different ways.
From this article you will find out how to set up the IP Matrix configuration on the VIDEOJET decoder 7000 (VJD-7513) using Configuration Manager.
The built-in IP Matrix functionality, together with a connected keyboard, allows VIDEOJET decoder 7000 to run as a stand-alone system.
An operator can manage up to 32 cameras via the keyboard without any PC or management system required. System setup is quickly done with Configuration Manager. After that, no PC is required to run the IP Matrix
According to the Release letter (Firmware 9.51) of VJD-7513, VIDEOJET decoder 7000 supports IP Matrix application as built-in feature.
According to the Release letter (Firmware 54.8.02) of VJD-7000, IP matrix remote monitor is only possible with UDP. TCP not supported.
** VJD-7000 can be used as an extended monitor to IP Matrix in single and quad view.
Please check also the following article and find out: Which are the system requirements for configuration/ operation of VIDEOJET decoder 3000/ 7000/ 8000?
A single system can support:
2 physical monitor displays
One KBD-Universal XF keyboard
32 camera sequences
9 favorite views
If your VIDEOJET decoder does not seem to work properly , most likely it is because the software (SW) version used is not compatible with the firmware (FW) version of your device.
But which are the system requirements for configuration/ operation purposes of VIDEOJET decoder 3000/ 7000/ 8000?
A password prevents unauthorized access to the device. You can use different authorization levels to limit access. Proper password protection is only guaranteed when all higher authorization levels are also protected with a password. Therefore, you must always start from the highest authorization level when assigning passwords.
This article will guide you step by step to set the destination password for decoders.
If you have the option "Extended (security)/configuration mode" active on a VIDEOJET decoder 7000 (VJD-7513) in Configuration Manager, then no video image will be shown and the BOSCH logo will be displayed at the cameo of the monitor output of the decoder.
This is as designed in Configuration Manager, and this mode is to give you the opportunity to enable the SSD Encryption and to disable the USB ports.
Once you are finished changing the extended security features, you must uncheck the check box and the decoder will go back to normal functioning.
Before you can operate your VIDEOJET decoder 7000/ 8000 within your network, it must have a valid IP address for your network and a compatible subnet mask.
This articles explains how you can change the IP Address of VIDEOJET decoder 7000/ 8000 using Configuration Manager.
HD Decoders are not downgrade-able lower than the factory default version.
All Video Management Systems should not have issues with newer Firmware. All their implemented functions should work.
NOTE: All new stock of VJD-8000 gets version 9.51 due to Security Vulnerabilities.
Please also see:
Which Bosch encoders and decoders are compatible with BVMS?
According to the BVMS 11. Release notes > 2.2. Removed functionality chapter > The digital monitor wall functionality has been removed.
This removal has impact on the BVMS Viewer → Decoders are not supported anymore in BVMS Viewer starting with version 11.0
Other devices and functions that have been removed to ensure software security:
Map migration (removed Autodesk design review installation)
Note: The Monitor Group functionality is still available in BVMS Professional/ Plus/ Lite.
This article explains how to integrate the Bosch MIC IP 7000 HD camera series into any existing analog CCTV system using the Bosch VIDEOJET decoder 3000. The most common integration scenarios are listed below:
Simple integration using direct connectivity to analog monitor and joystick, typically found in single camera installation (for example, mobile surveillance vehicles)
Integration into an existing analog matrix switcher typically found in large installations (such as for city surveillance)
Monitor Group gives operators flexible control over the content of a video wall or allows them to let the system take over this control automatically based on pre-defined scenarios.
This article describes h ow to create a Monitor Group on a decoder VJD 7xxx/ 8xxx in BVMS Configuration Client.
°Each decoder requires one or two channel expansion licenses (depending on the number of monitor ports available)
The current MG implementation requires the availability of the Management server during operation
Former Digital wall implementation has been removed in BVMS >=11.0
NEW BVMS v.11.0 feature
The configuration step 9+10 from this article can be done also using the “Protect iSCSI storage with global CHAP password” (Menu item under Hardware). In case the function has been already enabled, step 9+10 is obsolete.