Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Video

    Sort by:
    100% helpful (1/1)
    ‎11-22-2021 07:57 AM
    Please check which port and protocol have been set on the camera that has the live black image.
    View full article
    100% helpful (1/1)
    a month ago
    Network switch has port security on and shuts down a NetApp iSCSI data port (e.g. CH3). This article is only relevant in aspects of network security / port security where MAC addresses are analysed. Some network security applications are capable of sniffing network packets thoroughly enough to pick up MAC addresses on E-Series Controller ports that are not seen in the Storage Array Profile data.
    View full article
    100% helpful (2/2)
    ‎07-30-2021 12:23 PM
    This article will explain how to set-up the RAID quickly in order to start the "re-imaging" process from the Recovery DVD (one at DIVAR IP 6000 R2 - or two DVDs at DIVAR IP 7000 R2) enclose to each DIVAR IP 7000 R2 or DIVAR IP 6000 R2 delivery. 
    View full article
    100% helpful (1/1)
    ‎11-05-2021 04:30 PM
    Find out from this article which VRM version is compatible with your DIP and what BVMS version is supported.
    View full article
    100% helpful (1/1)
    ‎11-01-2021 12:10 PM
    If cleaning the bubble is required, use the following procedures and comply with all the warnings listed in this article.
    View full article
    100% helpful (1/1)
    ‎10-18-2021 11:27 AM
    This article lists how to configure ANR feature in BVMS and how correctly to set up iSCSI and direct replay.  Configuration   of   ANR in BVMS system Insert SD card into camera and power it on. In Configuration Client, select Devices page. Device password and CHAP password. There are two possible configuration set ups - to configure password for both device and iSCSI connection or to leave both without password. Choose and configure one of them (3.1 or 3..2).    3.1.  Set device user password and CHAP password 3.2.  No CHAP password for ANR Note: Mixing the parameters between the two options 3.1 and 3.2 will lead to issues in direct replay from SD card.
    View full article
    100% helpful (1/1)
    ‎10-13-2021 02:28 PM
    Traffic detector has been developed to cope with all traffic densities up to high density like congestions and queues in front of traffic lights. It also detects non-moving vehicles and is thus applicable for smart parking. In addition to vehicles, it also detects pedestrians. Applications  Tunnels & Highways: o Collection of traffic statistics o Detection of congestions for automatic speed signaling o Detection of wrong way driving  Intersections: o Detecting presence and volume of vehicles  Smart parking: o Detect parked cars
    View full article
    100% helpful (1/1)
    ‎09-28-2021 11:55 AM
    With the DSA E2800 Bosch introduced Multipathing. It is a fault-tolerance technique that defines more than one physical path between the camera and its iSCSI storage devices through redundant network connections. When using this feature, recording of video data and replaying video data is possible even in case of an iSCSI controller failure. To ensure also that outages of infrastructure equipment (e.g. Switch) could be covered, we recommend following Interconnection.  
    View full article
    100% helpful (1/1)
    ‎09-28-2021 11:50 AM
    This article describes the easiest method for adding Expansion shelves to a Base unit DSA E-Series E2600, E2700 or E2800.   This article also applies when: The amount of storage is overloaded and you need additional storage after fully populating the base shelf.   Article requirements: 1. Configuration Manager 2. Configuration Client which is included with BVMS 3. Santricity Software   Step-by-step guide      
    View full article
    100% helpful (1/1)
    ‎09-28-2021 11:22 AM
    BVMS v10.1 and  BVMS v11.0 come with a checkbox where you can logon to the Operator Client with Windows Credentials. If you want to use this function, you need to set up the BVMS Configuration Client and browse the AD users-groups. Then, the users can sign in to Operator Client with their Windows-Credentials. 
    View full article
    100% helpful (1/1)
    ‎08-23-2021 02:42 PM
    You can find it in the   Configuration Client   > Main window >   Settings   menu >   Remote Access Settings... command >   Show Port Mapping... button >   Port Mapping Table dialog box Port Mapping Table dialog box displays the port mapping for the IP addresses of the configured devices in your BVMS. You can find here the private and public ports that are in use in the BVMS system.   Example:     Used ports: All local ports   that must be open on the computer where the server is installed or on the router/ level 3 switch that is connected to the server   can be found in Help section (F1)   from Configuration Client or you can see some useful examples, Q&A and specific cases in the following Knowledge Base article: Which are the ports that must be open within a LAN for all BVMS components?
    View full article
    100% helpful (1/1)
    3 weeks ago
    Find out from this article in which situations the  MAC address cannot be found or only part of the address is correctly extracted in Project Assistant when scanning a QR or Data Matrix code
    View full article
    100% helpful (1/1)
    ‎11-25-2021 03:40 PM
    This article describes how the integrity of BVMS software can be checked.
    View full article
    100% helpful (4/4)
    ‎08-23-2021 09:07 AM
    This article informs about improvements in firmware handling and new security mechanisms that help our customers to increase security related to firmware updates and IP camera protection.
    View full article
    100% helpful (1/1)
    ‎08-11-2021 03:16 PM
    This articles gives a short introduction to scripting alarm and counter tasks with Intelligent and Essential Video Analytics in FW 7.60. It also provides a broad selection of example scripts for explanation as well as including real world application examples.
    View full article
    100% helpful (1/1)
    ‎10-14-2021 04:09 PM
    This article describes the camera tamper detection options available with FW 6.30: Scene too dark / bright, global change, reference image check. Applications: - Detect camera blinding - Detect camera being moved away from of its view - Detect the loss of sufficient overall illumination - Detect idle / removed objects, e.g. objects in front of an emergency exit Limitations: - Not available on thermal cameras
    View full article
    100% helpful (5/5)
    ‎07-28-2021 04:01 PM
    BVMS - Automatic login of Operator Client: The BVMS Operator Client can be automatically logged in by using parameterized startup.
    View full article
    100% helpful (1/1)
    ‎05-31-2022 02:34 PM
    This article contains the correct default IP address of Videojet decoder 8000 at the factory default
    View full article
    100% helpful (3/3)
    ‎08-06-2021 10:33 AM
    Communication can get interrupted and configuraiton might fail if the below desribed actions are not performed. If your system is affected or not is described here as follows: There can be authentication issues between the BVMS Central Server and the Video Recording Manager in case they are installed on different Servers. It is possible to see reports at the BVMS 8.x system alarms that VRM reports   wrong version Please check in the VRM debug logging if the following logline indications can be found
    View full article
    100% helpful (2/2)
    ‎11-25-2021 02:59 PM
    Want to know how flexible BVMS can assign streaming profiles to cameras?
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist