Security: Video

The RCPP command to enable/ disable the privacy masks is CONF_PRIV_MSK_POLY - 0x0bd8. Follow this article to see the rcpp command to enable & disable the privacy mask of a Bosch camera (moving or fixed).

Check this article to learn about what to do when a FLEXIDOME multi 7000i (IR) or FLEXIDOME panoramic 5100i (IR) does not boot up or is unresponsive.

In contrast to the moving objects detected in general by IVA 7.10, Camera Trainer allows detection of both moving and non-moving objects, separates, and immediately classifies them. Learn more about Camera Training from this article!

If you have for example a DIVAR 7000 AIO as central BVMS server and also, on the same network, you have a DIVAR Network Video Recorder (NVR) to which cameras are connected to and recording, the recording is typically handled by the NVR itself. Therefore, in this case the cameras added on the NVR will continue recording only there because the NVR manages the recording and storage of video footage from them.

This article explains why the Live view shows ‘Authentication failed’ in Video Security App.

MVS gets error message “Videoprovider not available” when trying to log on. Also, the BVMS Configuration Client shows the X mark on the MVS. What to do?

If one of DIVARs IP 5000 AIO is selected on a user profile, the Operator Client opens the site and works fine. One message is displayed when two or more DIVARs are added into the same Enterprise system.   If you already have a DIP 5000 AIO into your Enterprise system and you want to add additional units but you receive the following message, you can solve this by using the steps below: "Server of configuration database is already in the server list. Remove either the server that is twice in the list or make sure that the configuration database is not cloned between servers."

The maximum zoom speed in the GUI is operational but is only applicable during "manual control." When the operator calls for 30x, the zoom speed has to remain constant. While the speed may not be as rapid as anticipated, it is essential to understand that this camera model is already operating at its optimum capacity.

The "Lens rotation" slider can be used to correct for any manual lens rotations performed during installation. If the lens is manually rotated during installation, the slider value should be aligned with the rotation value shown on the lens.

If the ‘decoder offline’ message occurs during the FW upgrade from 54.7 to 54.8,  try to use another version of Configuration Manager, or remove the password temporarily.

This article provides an answer regarding what to do in case if a  colleague from the same company claimed a license with a wrong Remote Portal account.

This article explains step-by-step how to add and keep the purchased licenses in my Remote Portal account. Upon purchasing licensing, an email from Bosch provides the needed codes.

Health monitoring with Remote System Management is very easy, as in one page you have an overview of the state of all DIVAR IPs connected to your Remote Portal and then, drilling down a level, you have an instant overview of the state of the cameras connected to the selected DIVAR IP. A service is available to setup health alerts for devices via email, so you are informed when any emergencies pop up.

To find out the Windows version compatible with BVMS (Bosch Video Management System), you should consult the Release Letter. BVMS compatibility may vary depending on the specific version of BVMS you are using.

Perform an update in the BVMS setting to pull h265 and the recording should start to show up in the playback cameo from BVMS Operator Client

DIVAR 5000 network or Hybrid do not support KBD-UXF. However, the KBD-DIGITAL is still a current product and can be used.

"An unexpcted error occured. Press F5 to go back to the operation mode selection page and retry. If the issue persist, contact technical support." Windows Server 2022, which is running on these machines is trying to contact their server, which in some cases (still being investigated why) is failing.  

During the BVMS upgrade from v11.1.1 to v12.0 through System Manager v2.0 on the DIVAR IP 6000 AIO, the software file placed on an external drive is not visible to be installed. What could be the cause?

Regular BVMS 12.0.1 installer will not run on any DIVAR IP all-in-one platform. The upgrade shall be performed via DIVAR IP System Manager application. Keep in mind: If you want the latest version of BVMS, it must be downloaded and applied with the latest version of System Manager.

This article explains how to configure the Bosch ITS and NTCIP licensed versions of IP moving cameras to respond to National Transportation Communications ITS Protocol (NTCIP).