Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    How to setup an INT-TXO Integrus Transmitter OMNEO?

    Introduction

     

    The new INT-TXO Integrus Transmitter integrates the Integrus system in the DICENTIS via OMNEO. Old Radiators and Receivers stay the same and existing equipment can be used in the DICENTIS now with the new INT-TXO transmitter. It is usable from software version 4.20 onward and is made for DICENTIS only usage at the moment. But it will be open up in future for the usage of 3rd party devices which than are planned to be managed with the Dante Controller software. Please visit our product page for more information. 

     

    Front

    Central_Support_0-1692707365920.png

     

    Back

    Central_Support_1-1692707388892.png

     

    Overview of the new Integrus system:

     

    Central_Support_2-1692707416724.png

     

    Overview of the old system designed for the usage of DCN-NG or to use as stand alone system:

     

    Central_Support_3-1692707443591.png

     

    How to setup

     

    First install the INT-TXO into an rack and and insert the power.

    The preferred way to power the TXO is to use an DCNM-APS or PS because you than can switch it completely off and on with your DICENTIS software. If you use an POE port from an switch or the included external power supply it will switch only into standby mode if you turn the DICENTIS system off. Which free network port you are using to connect anywhere in the DICENTIS cloud is not important. The device behaves (is) similar to an two port switch like every DICENTIS devise which makes it very flexible were you can connect it and daisy chain. For that it provides an wide cable range of 100m between each DICENTIS unit. (Ethernet specification IEEE 802.3ab)

    Central_Support_4-1692707531692.png

     

    Accessories

     

    The TXO comes with an external PSU the same as for the DCNM-WAP with universal AC adapters for different country's. Output 48V 0,5A 24W + standard rack mounting brackets.

    Central_Support_5-1692707570972.png

     

    Connection Expel

     

    The INT-TXO can be connected to any point in the DICENTIS cloud for example to a DCNM-Idesk, DCNM-MMD or directly to an DCNM-PS and it's only limiting factors are hop counts (if RSTP is used) and 11W  Power consumption which must calculated like before with any other DICENTIS device. An power calculation tool is provided within our DICENTIS software to help you to calculate your system easily. https://licensing.boschsecurity.com/software/html/pages/home/

    Central_Support_6-1692707600252.png

     

    DICENTIS Power Calculation Tool can be found in our Software under Tools.

    Central_Support_7-1692707646226.png

     

    Power switch

     

    If you use power insert via the DCNM-APS or PS you can switch the TXO completely OFF an ON with the DICENTIS Meeting Application.

    Central_Support_8-1692707693665.png

     

    In this case the unit will be totally off without power consumption.

    Central_Support_9-1692707720694.png

     

    But if you use an POE or PSU to power the INT-TXO it will only change into standby mode.

    Central_Support_10-1692707749382.png

     

    This is the LED indication table to check if an error occurred or if your settings are correct.

    Central_Support_11-1692707774306.png

     

    The second step is to check the status if the TXO has the right firmware version. If not please do an firmware upload to your version but at least to 4.20. (Please use the newest version >5.1 to benefit of improvements bug fixes)

    13.png

    The Minimum DICENTIS Software requirement is 4.20 or else the TXO will not work. The DICENTIS software iso which include the Firmware Upload Tool can be found here.

    Central_Support_12-1692707846301.png

    Next open an browser and type in

    https://int-txo.local/

    All settings are done via this web page.

     

    Login

     

    Central_Support_13-1692707905141.png

     

    Flip the the Master Slave switch two times.

    Central_Support_14-1692707940434.png

     

    Start you registration and set you password.

    Central_Support_15-1692707977777.png

     

    Press Login

    Central_Support_16-1692708026671.png

     

    You are now logged in and have access to other menu parts to configure the TXO.

    Central_Support_17-1692708078741.png

     

    Transmitter status

     

    Here you can check the Presence of Radiators and initiate an test tone which can be checked for example on the receivers.

    Central_Support_18-1692708106256.png

     

    In this example I only have attached one Radiator and using it as Master.

    Central_Support_19-1692708134519.png

     

    HF Out

    Central_Support_20-1692709137915.png

     

    Select Test tone to all.

    Central_Support_21-1692709181809.png

     

    Now take your LBB4540/xx with an Headset (LBB3443) and switch it on.

    You should now hear an sinus tone which is increasing in frequency form 0 to 3.

    0 is the floor and 1 2 3 are the usable languages. The INT-TOX is in the basic version only with 4 channels of IN- and OUT- puts provided. Additional language channels can be bought with an license.

    Central_Support_22-1692709211625.png

     

    It is possible to check the signal strength with the LBB4540/xx from the radiators.

    Central_Support_23-1692709245259.png

     

    Central_Support_24-1692709287815.png

     

    or more details please have a look at the Integrus manual which comes with the new 4.20 SW how to configure it.

     

    All manuals regarding the DICENTIS are provided within our software under Docs.

    Central_Support_25-1692709315003.png

     

    Conference Protocol documentation & API

     

    Also we providing for the INT-TXO an Conference Protocol documentation if you need to create an API.  ( for application development) which can be found as well on the

    Central_Support_26-1692709351141.pngCentral_Support_27-1692709560433.png

     

    Additional important information

     

    Receivers as well the Radiators have an cover angle and the installation must be planned carefully to avoid interference. Due to the infrared light technologies signal shadows can occur behind objects and direct sight to the Radiators is recommended.  

     

    Central_Support_28-1692709588698.png

     

    More regarding beam behavior and delay in the manual.

    Central_Support_0-1692711605106.png

     

    Carefully room planning is needed.

    Central_Support_1-1692711673100.png

     

    Central_Support_2-1692711690630.png

     

    Central_Support_3-1692711709650.png

     

    Carrier management

     

    Don't change during a conference the Carrier management since a rest will happen. Each Carrier can host four audio channels.

    Central_Support_4-1692711757664.png

     

    General settings

     

    Central_Support_5-1692711796155.png

     

    System info

     

    Here you have the option to change your host name and access page. If you have more than 1 Transmitter name it for example after the room wher it is used. int-maincourd. = https:// int-maincourd.local/

    Central_Support_6-1692711858801.png

     

    Settings within the Meeting application

     

    To hear the different translations you need to add them in the Language selection within the Meeting application. In the standard usage the translation channels were created form translators with DCNM-IDESKs so that Interpreter desks needs to configured as well.

    In the standard the INT-TXO provides 4  in and out put channels. Additional language channels must be bought.

    For example in this case as picture below.

    0=floor

    1=German

    2=English

    3=French

    Central_Support_7-1692711930705.png

     

    Now you can hear the German translation channel. The toggle button let you choose the correct translator channel.

    Central_Support_8-1692711959769.png

     

    For example this is how an Interpreter desk could be configured.

    Central_Support_9-1692711988255.png

     

    Password reset

     

    In case you forgot your password for the web interface press the reset button for 10 seconds to delete all settings.

    Central_Support_10-1692712016999.png

     

    The green flashing data light will go off from your network cable.

    Central_Support_11-1692712052305.png

     

    And the LEDs will change if the reset is done correctly.

    Central_Support_12-1692712098710.png

     

    Now you can start all over again and configure your transmitter from the beginning but you need to be on side since an flip of the Master Slave switch is necessary to proceed.

    Central_Support_13-1692712137925.png

     

    Licensing

     

    The TXO come with an standard 4 send and received license. If you need more language channels you need to buy a license.

    Up to 32 Channels are available additional of 28 INT-L1AL can be bought. (F.01U.406.935)

    Central_Support_14-1692712189507.png

     

    If you by an license you will get an Entitlement Certificate from Bosch.

    Central_Support_15-1692712261639.png

     

    How to activate licenses

     

    Enter all your contact data , Add the Activation ID and create an license request file.

    Central_Support_16-1692712299577.png

     

    This is the request file.

    Central_Support_17-1692712348693.png

     

    Go to the System Activation site and log in with your technician account.

    Central_Support_18-1692712379966.png

     

    Enter your password.

    Central_Support_19-1692712422429.png

     

    Choose Manage license

    Central_Support_20-1692712456260.png

     

    Select the INT-TXO created request file.

    Central_Support_21-1692712490539.png

     

    Press on Process

    Central_Support_22-1692712519027.png

    An file will be created if successful transferred. Please contact the technical support if an error occurred here.

    Central_Support_23-1692712556880.png

     

    Brows in the TXO Licensing page for the ResponseRequest file which were created via the System Activation Site

    Central_Support_24-1692712587849.png

     

    Central_Support_25-1692712636577.png

     

    Process the response message.

    Central_Support_26-1692712697618.png

     

    If everything was working fine a new column is created in the web page under Licensing.

    Central_Support_27-1692712742054.png

     

    It is also mentioned under System info.

    Central_Support_28-1692712786313.png

    If you want to use now your new added translator channels you must add them as well in the Meeting application.

    Central_Support_29-1692712842812.png

     

    It is now possible to go up to 31 translator channels in the LBB4550/32

    Central_Support_30-1692712885694.png

    As example the Interpreter settings could be like this.

    Central_Support_31-1692712913327.png

     

    To be able to use all 32 channels you also need an receiver witch is capable of that. (LBB4540/32)

    Central_Support_32-1692712971951.png
    Central_Support_33-1692712991392.png

     

    An Factory default reset will not delete this license.

    Central_Support_34-1692713047318.png
    Central_Support_35-1692713078833.pngCentral_Support_36-1692713104557.pngCentral_Support_37-1692713156576.png

     

    Return of license

     

    If you ever need to return the license copy the mac address.

    Central_Support_38-1692713208875.png

     

    Log into the System Activation Site with an technician account.

    Central_Support_39-1692713235954.png

     

    Search in the Overview under Fulfillment ID with the copied MAC address.

    Central_Support_40-1692713257609.png

     

    Select Location

    Central_Support_41-1692713276527.png

     

    And than Return Licenses

    Central_Support_42-1692713299382.pngCentral_Support_43-1692713316432.png

     

    Press under Licensing the Brows button and open the new created ReturnRequest file

    Central_Support_44-1692713345047.png

     

    Press on Process response massage.

    Central_Support_45-1692713366370.png

     

    The Integrus will create an ReturnResponse file.

    Central_Support_46-1692713392308.png

     

    Process the  ReturnResponse file in the System Activation Site to release this license.

    Central_Support_47-1692713414957.png

     

    If everything worked fine you will get an green success message.

    Central_Support_48-1692713441949.png

     

    If you search now with your Activation ID on the System Activation Site you will see that your license is free to use.

    Central_Support_49-1692713464759.png

     

    Troubleshoot

     

    1) If you have problems to activate or give back your license please contact the Technical Support for help. This is the list for EMEA without ASIA and AMERICA.

     

    Central_Support_50-1692713503451.pngCentral_Support_51-1692713529116.png

     

    2) Please don't use this special cataract signs in the in the activation columns under Licensing! We once had a case were this special cataract Ō (Denmark) caused a problem with the activation file and later an customer from Czech Republic had a problem with an ě.

    Also an Spain customer had problems with ñ Ñ , á Á, é É, í Í and ú Ú. And a German dealer had a problem with "Straße" ß.

    Central_Support_0-1700222742300.png
    Central_Support_53-1692713691011.png
    Central_Support_54-1692713704601.png

     

    3) Also there was an overlay discovered if you use >=6 IDesks. It will unfortunately send the 5th translation channel to 1st instead. Improvements are expected to be solved in DICENTIS version 5.10.

    Version history
    Last update:
    3 weeks ago
    Updated by:
    Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist