How to Configure FPP-RNAC-8A-4C on an Option Bus panel

[#1]

**NOTE: Panel NAC outputs will not be in sync with the NAC output devices connected the the FPP-RNAC-8A-4C.

FPD-7024 - A Maximum of 4 FPP-RNAC-8A-4C can be added to the Option Bus.

FPP-RNAC-8A-4C Dipswitch Settings

All Dipswitches OFF on Dipswitch Bank S1

Dipswitch Bank S2 - Dipswitch 0 Off - Dipswitches 1 & 2 set the AC Failure Delay

Dipswitches	0	1	2
No Delay	Off	Off	Off
1 Hour Delay	Off	Off	On
3 Hour Delay	Off	On	Off
6 Hour Delay	Off	On	On

Dipswitched 3,4,5,and 6 Set the option Bus Address

Dipswitches	3	4	5	6
Disabled	Off	Off	Off	Off
Address 1	Off	Off	Off	On
Address 2	Off	Off	On	Off
Address 3	Off	Off	On	On
Address 4	Off	On	Off	Off
Address 5	Off	On	Off	On
Address 6	Off	On	On	Off
Address 7	Off	On	On	On
Address 8	On	Off	Off	Off
Address 9	On	Off	Off	On
Address 10	On	Off	On	Off
Address 11	On	Off	On	On
Address 12	On	On	Off	Off
Address 13	On	On	Off	On
Address 14	On	On	On	Off
Address 15	-	-	-	-

 *Note - Each device on the option bus of the FPD-7024 requires a unique address.

 FPD-7024 Panel ProgrammingEnter Program Mode on the FPD-7024

1.) Press 0 and Enter your program pin (Default  is 9876).  The display should read Program Modes on the top line of the display.                                                                                                             2.)  Press 3 for Program System
3.) Press 4 for Option Bus
4.) Press 1 for Update Bus *** The keypad will display “Updating . . .  TOT BUS DEVS: XX”.  "XX" = the total number of devices on the Option bus. If (00) or the incorrect total number of devices on the bus appears, check the wiring and addressing of each device on the Option bus.  Each Device needs to have a unique address. Then repeat steps above until all the devices are learned to the Option Bus of the panel. ***
5.) To Exit Programming, press the "*/Back" button 4 times

______________________________________________________________________________________________________

 **NOTE: Panel NAC outputs will not be in sync with the NAC output devices connected the the FPP-RNAC-8A-4C.

FPA-1000 - A Maximum of 4 FPP-RNAC-8A-4C can be added to the Option Bus

All Dipswitches OFF on Dipswitch Bank S1

Dipswitch Bank S2 Dipswitch 0 Off -Dipswitches 1 & 2 set the AC Failure Delay

Dipswitches	0	1	2
No Delay	Off	Off	Off
1 Hour Delay	Off	Off	On
3 Hour Delay	Off	On	Off
6 Hour Delay	Off	On	On

Dipswitched 3,4,5,and 6 Set the option Bus Address

Address 11	On	Off	On	On
Address 12	On	On	Off	Off
Address 13	On	On	Off	On
Address 14	On	On	On	Off

*Note - Each device on the option bus of the FPA-1000 has defined assigned addresses. The FPP-RNAC-8A-4C address options are 11 - 14.

FPA-1000 Panel Programming
1.) Press the enter button
2.) Choose 6 for Program
3.) Enter the program pin (Default is 3333)
4.) Choose 9 for Auto Learn
5.) Choose 5 for Update Option Bus (This will display the # of device it finds on the option bus) 
*** If (00) or the incorrect total number of devices on the bus appears, check the wiring and addressing of each device on the Option bus. Each device needs to have a unique address. Then repeat steps above until all the devices are learned into the Option Bus of the panel. *** 
6.) To exit programming, press the ESC button 4 times.

 **NOTE: Panel NAC outputs will not be in sync with the NAC output devices connected the the FPP-RNAC-8A-4C.