About CPrince

Overview: The FA422 Programming Cable has a 2 pin female connector at the transmitter end. Inovonics transmitters have 3 pins on them. The center pin on the transmitter is for Data and the 2 outer pins are ground. The 2 pin connector connects to the center pin and either of the outer pins on the transmitters when programming. Issue The programming cable for the FA422 receiver only has 2 pins at the transmitter end. How does the 2 pin connector connect to the 3 pin transmitter? Solution Connect the 2 pin connector to the center pin and either outer pin. Either way will work. ... View more

Issue While using Command 56 to enter/change passcodes, the screen goes blank after entering the user number and pressing enter. Solution The name text is blank in programming for the User Name. The default text for any given user is 'USER' followed by the number of the user. Simply press enter to continue and the Command 56 process will continue as specified in the literature. The Use Name Text can be added with RPS or D5200 panels up to GV3 8.05 Firmware.  Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, D1255, D1260, D1265 ... View more

  Issue How can a code be deleted on the DS7400xi panels? Solution Use the following steps to change a passcode: Enter the master code, and press [#], [0]. Press [0]. Enter the user number (001 to 090) (001-200 version 4 only). Enter the authority lever (0 – 6). See below. Enter the area the user has access to (1- 8), or press [#] for all areas. Enter the new PIN. The new PIN must be four digits long. Enter the new PIN again, and then press [#]. Authority Levels 0 = Master Code 1 = Unlimited 2 = General 3 = Arm Only 4 = Temporary 5 = Duress 6 = Access Code To Delete a User Select the User Slot followed by the # key. *Note: User 001 cannot be deleted in this manner, it must be changed in programmers mode. Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4, DS7447 ... View more

Overview: Keypad displays  a flashing "service perimeter" because a zone is or was faulted. Issue Keypad displays a flashing "Service Perimeter" with no zones displayed.   Solution   A Perimeter zone is or was faulted. If a zone is displayed, the zone must be made normal first. If no zone is displayed,  enter CODE + ENTER + CLEAR + CLEAR . This will clear the keypad memory. ... View more

Issue How can I change the display on the Command Center?   Solution   Control Change Display with COMMAND 49 This function presents three options: Dim the display Brighten the display Continuously show the time and date in the display Bright/Dim You can brighten or dim your command center’s display. When the display is dim, the tones are softer than those when the display is bright. Use this option for command centers in bedrooms where a brighter display and louder tones could interfere with sleep. If you dim the command center display and an alarm or trouble condition occurs, the display automatically brightens and the volume increases. The display returns to dim lighting when you clear the alarm or trouble condition. Continuous Time/Date Use this function to: Replace the disarmed idle text with a continuous time and date display Prevent passersby from knowing the status of your system. Display the date and time during normal system operation Any time your command center has an event to display, the time and date display are automatically removed. To return the time and date display, you must perform this function again. Ensure that your command center is at idle text. Press the COMMAND bar. The display shows SYSTEM COMMAND. Press the 4 key, followed by the 9 key. NOTE: If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function. Press the MENU key to enter the Command Menu, then press NEXT repeatedly until you reach the CHG DISPLAY ? prompt. Press ENT. The display shows BRIGHT DISPLAY ?. Press ENT to brighten the display. If you wish to dim the display or continuously show the date and time, press NEXT. The display shows DIM DISPLAY ?. Press ENT to dim the display. If you wish to continuously show the time and date, press NEXT. Note: If your system is turned on (armed), you cannot display the time. TIME DISPLAY ? displays. Press ENT to continuously show the date and time. Pressing ESC with the time and date showing returns the display to idle text. Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G ... View more