About CPrince

*Note: In all popit based panels when deleting a popit it is a good practice to remove the popit (D9127T/U) from the popit loop. This prevents the panel from displaying the popit as and extra point in the future, In the older popit based panels (B, B1, G, GV2, GV3) to disable the popit point you just need to set the Point index to (0) and remove the popit from the loop. In GV4 Series, B8512G and B9512G you need to do three steps. Set the Point Index (Point Profile) to (0), set the Point Source to (Unassigned) and remove the popit from the loop.  ... View more

FPD-7024 Keypad programming to Setup Network Card * Note: The panel mother should be RED with a Firmware reversion of 1.03 to support Ethernet communications.  Connect the Network card to the option bus. (*The DX4020 needs to be addressed as 250, all switches On / CLOSED.) connected to the panel. B420 and B426 Set the Rotary Switch to 9 = Address 250 Keypad Programming Steps 1) Press 0 Enter 9876 2) Press 3 Program System 3) Press 4 Option Bus 4) Press 1 Update Bus – The keypad will display “Updating . . .  TOT BUS DEVS: XX”. XX = the total number of devices on the Optionbus.      If 00 or not the correct total number of devices on the bus, check the wiring and addressing of each device on the Option bus. Each Device needs to have it own address. Repeat steps 3 and 4 until all the devices learned in the panel. 5) Press 7 Remote Program 6) Press 1 Enable 7) Press the * / Back key Once the top line of the display should read “PROG MODES”. 😎 Press 6 Program Accounts 9) Press 7 Alternate Communication – Select 0 Network 10) Press * / Back key once 11) Press 5 Communication Attempts Enter 05 # 12) Press 1 Phone / IP Number 13) Press 1 Phone / IP 1 14) Press 1 Enter 0 to tell the panel this is an IP Address (then enter the 12th digit IP Address of the Central Station) followed by the ACK Wait 015 -  then the Poll Rate 180 followed by Anti - Replay 1#Enter. The complete string would be01730840330820151801 if reporting to IP 173.84.33.82 with 5 Minute Supervision. 15) Press 2 Port Number Enter 07700#Enter (Default Port) or Port number used by the Central Station 16) Press 3 Format Select 7 Modem Format 17) Press 4 Account Number (enter you 4 digit account number followed by #) 18) Press the * / Back key Once the top line of the display should read “Phone / IP Number” Setting a Second IP address (if necessary) If reporting via IP the second path needs to be a different receiver, not the same receiver with 2 IP addresses to it. 1) Press 2 Phone / IP 2 to setup a second IP address if needed 2) Press 1 Enter 0 to tell the panel this is an IP Address (then enter the 12th digit IP Address of the Central Station) followed by 0151801#Enter 3) Press 2 Port Number Enter 07700#Enter (Default Port) or Port number used by the Central Station 4) Press 3 Format Select 7 Modem Format 5) Press 4 Account Number (enter you 4 digit account number followed by #) 6) Press the * / Back key Twice the top line of the display should read “Program Accounts” 7) Press 4 Ring Count Enter 02 # 😎 Press 7 Alternate Communications 9) Press 0 Network 10) Press the * / Back key 4 times to return to System Normal. **NOTE: If only using one IP path to the CS, Program Report Steering to PHONE 1 ONLY 1)   Press 0 Enter 9876 2)   Press 6 Program Accounts 3)   Press 3 Report Steering 4)   Press 11 5)   Press 21 6)   Press 31 7)   Press 41  😎   Press 51      9)  Press 61  10)  Press 71  11)  Press 81 12)  Press 91  13) Press the * / Back key 4 times to System Normal DX4020 Telnet Settings Note: The EPROM version of the DX4020 must be 2.21 or higher to be compatible with the FPD-7024. Now that the FPD-7024 is configured properly, the DX4020 needs to be programmed (telneted) to communicate with it. Refer to the DX4020 Installation Guide for more detailed instructions on DX4020 programming. The DX4020 needs to be address 250 all dip-switches closed. Channel 1 Parameters Baud rate - 9600 IF Mode - 4C Flow - 00 Port – 7700 (Default Port) Connect Mode - CC Data gram – 02 ... View more

**NOTE: Panel NAC outputs will not be in sync with the NAC output devices connected the the FPP-RNAC-8A-4C.   FPD-7024 - A Maximum of 4 FPP-RNAC-8A-4C can be added to the Option Bus. FPP-RNAC-8A-4C Dipswitch Settings All Dipswitches OFF on Dipswitch Bank S1 Dipswitch Bank S2 - Dipswitch 0 Off - Dipswitches 1 & 2 set the AC Failure Delay Dipswitches 0 1 2 No Delay Off Off Off 1 Hour Delay Off Off On 3 Hour Delay Off On Off 6 Hour Delay Off On On   Dipswitched 3,4,5,and 6 Set the option Bus Address Dipswitches 3 4 5 6 Disabled Off Off Off Off Address 1 Off Off Off On Address 2 Off Off On Off Address 3 Off Off On On Address 4 Off On Off Off Address 5 Off On Off On Address 6 Off On On Off Address 7 Off On On On Address 8 On Off Off Off Address 9 On Off Off On Address 10 On Off On Off Address 11 On Off On On Address 12 On On Off Off Address 13 On On Off On Address 14 On On On  Off Address 15 - - - -  *Note - Each device on the option bus of the FPD-7024 requires a unique address.  FPD-7024 Panel ProgrammingEnter Program Mode on the FPD-7024 1.) Press 0 and Enter your program pin (Default  is 9876).  The display should read Program Modes on the top line of the display.                                                                                                             2.)  Press 3 for Program System 3.) Press 4 for Option Bus 4.) Press 1 for Update Bus *** The keypad will display “Updating . . .  TOT BUS DEVS: XX”.  "XX" = the total number of devices on the Option bus. If (00) or the incorrect total number of devices on the bus appears, check the wiring and addressing of each device on the Option bus.  Each Device needs to have a unique address. Then repeat steps above until all the devices are learned to the Option Bus of the panel. *** 5.) To Exit Programming, press the "*/Back" button 4 times ______________________________________________________________________________________________________  **NOTE: Panel NAC outputs will not be in sync with the NAC output devices connected the the FPP-RNAC-8A-4C. FPA-1000 - A Maximum of 4 FPP-RNAC-8A-4C can be added to the Option Bus All Dipswitches OFF on Dipswitch Bank S1 Dipswitch Bank S2 Dipswitch 0 Off -Dipswitches 1 & 2 set the AC Failure Delay Dipswitches 0 1 2 No Delay Off Off Off 1 Hour Delay Off Off On 3 Hour Delay Off On Off 6 Hour Delay Off On On   Dipswitched 3,4,5,and 6 Set the option Bus Address Address 11 On Off On On Address 12 On On Off Off Address 13 On On Off On Address 14 On On On  Off *Note - Each device on the option bus of the FPA-1000 has defined assigned addresses. The FPP-RNAC-8A-4C address options are 11 - 14. FPA-1000 Panel Programming 1.) Press the enter button 2.) Choose 6 for Program 3.) Enter the program pin (Default is 3333) 4.) Choose 9 for Auto Learn 5.) Choose 5 for Update Option Bus (This will display the # of device it finds on the option bus)  *** If (00) or the incorrect total number of devices on the bus appears, check the wiring and addressing of each device on the Option bus. Each device needs to have a unique address. Then repeat steps above until all the devices are learned into the Option Bus of the panel. ***  6.) To exit programming, press the ESC button 4 times.  **NOTE: Panel NAC outputs will not be in sync with the NAC output devices connected the the FPP-RNAC-8A-4C. ... View more

 Bosch Security Knowledge Base Make sure the AC voltage  selection switch of the FPP-RNAC-8A-4C is configured for the correct incoming voltage to power, either 115V or 230V. The selection switch is located under the silver heat sink in the upper left corner. ... View more

Each panel needs its own unique Account Number to identify which panel is reporting to the CS (Central Monitoring Station).  Required programming for one panel reporting for all networked panels: DISABLE both PSTN and IP on the panels that are not directly reporting to the CS.  Assign a unique Account Number to each panel. Select the Communication type, PSTN for Phone or IP if reporting via network. It is possible to use Both Phone and IP - or any combination of Phone lines or IP for reporting to the CS. Select NETWORK WIDE for reporting for each panel  (if want only one panel to report for all). *Note if reporting IP, the CS must have a D6600 or D6100i Receiver setup for IP Communications. Required programming for each panel to report for itself: Assign a unique Account Number for each panel. Select the Communication type, PSTN for Phone or IP if reporting via network It is possible to use Both Phone and IP - or any combination of Phone lines or IP for reporting to the CS. Set each panel as PANEL WIDE for reporting. *Note if reporting IP, the CS must have a D6600 or D6100i Receiver setup for IP Communications. ... View more