About JuanVargasSSJ

Step 1: Create your door model and select ¨wiegand reader, keyboard¨   In case that the door was created previously without keyboard, it can be modified under the reader settings select type and select WIE1K reader   Step 2: Under options enable ¨access also by PIN code alone¨   Step3: Go to configuration, Options, PIN codes and select the desired PIN code length       Step 4: Go to Card reader and create type Dialog PIN card, two options available ¨Generate PIN¨ (I will generate a random PIN code) or ¨enter PIN¨ (user can enter customized PIN code)     Step 5: Go to card definition and enable Input mode   Step 6: Go to Personnel data, select Cards, select the right arrow under ¨record card¨ and select ¨Dialog  PIN card¨, enter the PIN code.    Notes:  Visitors are not allowed to use identification PIN codes only verification PIN Code. Make sure door is assigned to an authorization. Operation, to access via PIN code: Enter your PIN code followed by # ... View more

Step 1: Create a door model with keyboard or modify existing reader   Step 2: Under reader options enable PIN code required:     PIN code required= PIN code turned off (PIN code is disabled). PIN code required= PIN code turned on (PIN is required). PIN code required= PIN code controlled by time model (PIN code will be required when the time model is active). Access also by PIN code alone (Identification PIN code) can be used in conjunction with Verification PIN code. This means user is going to have a virtual card (identification PIN code) + a verification PIN code. More details about virtual card check: Step by Step how to configure Access via PIN code alone AMS.    Step 3: Go to configuration, ¨PIN codes¨ option and select the desired PIN code settings   Step 4: Go to Card definition and enable Input mode Step 5: Go to Personnel data, under PIN code option and set the Verification PIN code. Step Final : Operation:  Present card at the reader or enter identification PIN code, reader´s LED is going to start flashing then you enter verification PIN code.   ... View more

Applicable in scenarios when a manual egress is used instead of the automatic Door Opener. An input will shunt the door contact so an unauthorized access (e.g. Door Forced Open) event is not going to be generated and output ¨door opener¨ is not going to be triggered. This Input can be configured with a request to exit motion or a pushbutton. Open APE configurator, go to entrances, select ¨Local Open Enable¨ as your shunt only input.        Event under Logviewer will be displayed as message 66 Start Remote access from ext. switch. At this point door can be opened manually.   ... View more

1. Go to entrances and select ¨With keypad¨ option, then select: PIN code at entry reader select ¨Always¨ to enable verification at all times. ¨Per time Model¨ if verification is required on a specific time frame, ¨outside time model¨ or ¨outside time model at first use¨  if verification is required outside that time frame. 2. Go Configuration / Card definition and enable ¨PIN or Card¨ format.        3. Add a verification PIN Code for an specific user under personnel management software. 4. Operation mode present the card and type the PIN code followed by pound (#). ... View more

How to set up Interlock APE Example Interlock: Door 1 needs to be closed before you can open Door 2.   Note: It only works with 2 Doors. Example of door configuration:     Notice: If only one door is defined as part of a door-complex then the synchronization is not active.   Door #1 configuration: Door #1: Door contact assigned to input#1 Output for the maglock assigned to output #1 Entrance locked assigned to input #3 Input #3 is connected to output #4 (lock opposite direction) When input #1 is opened, it triggers output #3 that is connected to input #4 and it disables reader at Door#2     The output signal (Out 3) is to be set potential free (dry mode). The signal "door lock of opposite direction" must be closed (resistance=0) when de-energized. Use the "normally closed" (NC) contact of output 3.     Configuration for Door 2: Door #2: Door contact assigned to input#2 Output for the maglock assigned to output #2 Entrance locked assigned to input #4 Input #4 is connected to output #3 (lock opposite direction) When input #2 is opened, it triggers output #4 that is connected to input #3 and it disables reader at Door#1       ... View more