About CPrince

How do I upgrade/replace the panel MUX Expansion Module? Solution Perform the following procedure when upgrading/replacing the MUX expansion module: Receive the FACP programming with RPS. This programming will be sent back to the FACP later in this procedure. Remove the AC and battery power from the FACP. Remove the FPE-7039, D7039, or DS9431 MUX Expansion Module Card. Install the replacement FPE-7039, D7039, or DS9431 onto the FACP. Refer to the Installation Guide included with the MUX Card. Power the FACP on. If the message EEP INIT ERROR appears on the FACP display, press * or Back key to continue. Follow the prompts on the panel keypad, set the time and date, press * or Back key when the FACP finds the MUX expansion module and at the AUTO PROGRAM? Prompt, press 0 to select NO. Press PROG/0 to enter programming mode. Enter the PIN. The default PIN is 9876. Press 8 to select HISTORY DEFLTS. Press 2 to select DEFAULT EE. Press # to confirm, and then wait for the FACP to return to normal. Remove the AC and battery power from the FACP, then power the FACP on again. Connect at least one MUX device to the MUX BUSS. Power the FACP on. If the message EEP INIT ERROR appears on the FACP display, press (*) or Back key to continue. Follow the prompts on the panel keypad, set the time and date, press (*) or Back key when it finds the MUX Card and at the AUTO PROGRAM? Prompt, press 0 to select NO. Press PROG/0 to enter programming mode. Press 3 to select PROG SYSTEM. Press 7 to select REMOTE PGM. Press 1 to select ENABLE. Press * or Back twice. You should see PROG MODES on the first line of the display. Press 6 to select PROG ACC’NTS. Press 4 to select RING COUNT. Set the ring count to 02. Press #/CMD/Enter. Press (*) or Back 2 or 3 times to return the FACP to normal. From RPS, send the original program back to the panel. ... View more

Perform these steps to enable the D7024, FPD-7024, DS9400, DS9400I, and DS9400M for RPS programming via phone line with a compatible RPS modem: Press (0) Enter Program Mode. Enter Pin (Default is 9876). Press (6) Accounts. Press (4) Ring Count. Set Ring Count to (02) #. Press the (*) key two times or until you see PROGRAM MODES. Press (3) System. Press (7) Remote Program. Press (1) Enable. Press the (*) key five times to Exit Program Mode. You need to dial Line 1 on the panel. It is the second line down on the panel (it is NOT the line in the top right). Before connecting with RPS, perform an Auto-Learn with at least one Mux Device connected to the Mux loop, then send your RPS program to the panel. Press (0) Enter Program Mode. Enter Pin (default is 9876). Press (9) Program Mux. Press (4) Auto Program. Press (1) Yes. ... View more

The FPA-1000, FAP-1000-UL and FPA-1000-V2 all have the option to use 2 FPE-1000-SLC Loop cards. Each loop card on panel with Firmware less then 1.09 only support address 1 to 127 on each loop card, from firmware 1.10 and higher each loop card supports address 1 to 254. So it is possible to have to devices with the same address but on different loop cards. The the panel the keypad will display the following on the top line. The Event Type (Trouble, Fire, Supervisory) follow by XX-Y-AAA.A, (XX = Panel ID) (Y = Address Assignment, 0 - Web Page, 1 - SLC1, 2 - SLC2, Mainboard, or 4 - Option Bus) Followed (AAA.A The Device Address) . ... View more

 The FPC-500 Series Smokes are 4 -Wire technology, but if using more than one FCA-500 on the same loop it is a 6 wire configuration: 2 wires for power, 2 wires for the trouble loop, 2 wires for the alarm loop, and the last base on the loop needs to be a FCA-500-E (End of Line Base). If using only one smoke or installing them on and addressable loop the FCA-500-E base is required. The wiring configuration is, 2 wires for power and 2 wires for the alarm loop. Then for the trouble circuit you wire a jumper from terminal (T1) to terminal (b1/b2). Note: The last base on each loop of flush mount smoke detectors must be a FCA-500-E - Wiring is 4 conductor from the panel to the first head and 6 wires between the first base in the loop to the FCA-500-E base at the end of the loop. ... View more

The power card contains two jumpers located below the tamper switch: Tamper jumper: Enables or disables the housing cover tamper switch. Reset jumper: Enables or disables the remote keyswitch reset function. The power off reset functions normally regardless of the jumper setting. Jumper Location Jumper Setting. Cover both pins to Disable, remove jumper (store on 1 pin) to Enable. Issue The D341/D342 duct detector will not reset when using D344-RT Remote Test Kit.  Turning the key to Test puts the detector in the alarm condition but turning to Reset does not return the detector to normal condition. Solution The Reset Jumper on the power card inside the D341/D342 has not been removed to enable the Remote Keyswitch Reset function.  Remove the jumper below the tamper switch, on the right side. ... View more