About CPrince

 On the FPD-7024, D7024, DS9400, DS9400I, DS9400M panels program a relay to follow output 54 (Ground Start). *Note - PBX lines and ground start phone lines do not comply with NFPA requirements for digital communication. Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9465I, MX465, D7035, D7053 ... View more

Step-by-step guide   The D7052 (Figure 1) is a general-purpose module that connects to the multiplex bus of the control panel. It provides two supervised Class “B” input zones or one Class “A” input zone. Use a jumper pin setting for a Class “A” or Class “B” wiring configuration. The D7052 uses 2 points addresses when configure as Class B Inputs. You must not address the unit as a Multiple of 8 - so addresses 16, 24, 32, 40, 48, 56, 64, 72 . . . are not allowed and it programs as a Dual Point Device. See Figure 4. When wiring the D7052 Inputs as Class A, it is programmed as a Single Point Device. See Figure 3 for wiring. Wiring Class A and Programming as a Dual Point the next higher Address will be in trouble. Example - If the unit is address as 095 Point 096 will display trouble.   Part numbers D7052, D7024, FPD-7024, DS9400, DS9400I, DS9400M, MX363 ... View more

Select whether or not the arming state for an area changes from Master Armed to Perimeter Armed if no perimeter points with delay response are faulted during Exit Delay. Only the final armed state is reported and displayed at the keypads. *Note - When upgrading a non-GV2/GV3 control panel account to a GV2/GV3 control panel account, RPS forces the default to No. Parameter Options Yes: Switch the arming state to Perimeter if no Perimeter Delay point faults occurred. No: Keep the area in Master Arm if no Perimeter Delay point faults occurred. Part numbers D7212GV2, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B3512, B4512, B5512, B8512G, B9512G ... View more

Issue - Is the 192C compatible with the G-Series Panel? Solution Yes, it is compatible with the G Series panels with the 787 Ω, 2 W resistor across Terminals 6 (COM) and 7 (ALRM CKT+). Recommended is the D192G Bell Supervision Module. The panel selector jumper allows you to configure the D192C for either D8112 mode of operation or 2000 and 9000 Series mode of operation. The jumper in the D8112 position adds the filtering capacitor to the indicating output circuit. The jumper should be set in the D7112/D9112 position when used with the 2000 Series and 9000 Series (D9412GV4, D7412GV4, D9412GV3, D7412GV3, D7212GV3, D9412GV2, D9124GV2,D7412GV2, D7212GV2, D9412G, D9124G, D7412G, D7212G, D9412, D9124, D9112, D7412, D7212) Control Panels. In this position, the filtering capacitor is removed from the circuit and allows the panels to detect a missing battery condition. All new Bosch Security Systems control panels have the filter capacitor built into their power supplies. Part numbers D9412GV4, D7412GV4, D9412GV3, D7412GV3, D7212GV3, D9412GV2, D9124GV2,D7412GV2, D7212GV2, D9412G, D9124G, D7412G, D7212G, D9412, D9124, D9112, D7412, D7212, D192C, D192G ... View more

 Issue - Cannot change phone number and account number when keypad programming. All other program changes can be done.  Solution - Keypad programming partially blocked (Partial Anti Take-Over) this can only be unblock  with the programming software (WDSRP). Note - In WDSRP there is also another option to disabled All Keypad Programming. Panel part numbers DS7400XIVER3+, DS7060, DS7090, DS7090I, DS7090TM, DS7080I, DS7080IVER2, DS7080IP32, DS7090TMI, DS7100, DS7400, DS7400XIVER2, DS7400XIVER4+, DS7400X, DS7400Xi ... View more