About David

Procedure for sending or receiving the panel program: Connect the D5200 program cable between the D5200 Communicator port and the RJ-11 connector in the upper right corner of the D8112. Select the 8112 handler in the D5200 and press ENTER GROUP. Place the cursor on the correct 8112 version: D8112E, D8112E1, D8112G, D8112G1, D8112G2 or D8112A. Momentarily short Disable Restart (terminal 32) to Common (terminal 29). While the cursor is blinking beside the correct panel version, press RECV(COPY) to receive programming or SEND(LOAD) to send programming to the panel.  If the D5200 programmer has difficulty sending or receiving programming: Try removing serial data connections from the panel. Remove devices from terminals 29-32 by either removing wires from terminals, or remove the terminal strip from the right side of the control panel. Place a momentary short between Disable Restart (terminal 32) and Common (terminal 29). If the terminal strip has been removed, carefully place a jumper wire across the holes where terminal 29 and 32 would be.  If still receiving errors during attempts to copy the D8112: Check the D5200 programmer for adequate free memory and verify the 8112 handler is not corrupted. Turn on the D5200 and enter passcode Press the up arrow until DISK STAT displays and press ENTER GROUP. The following screen will appear: DISKSTAT Current Disk: A SizeKilobytes: 512 FreeKilobytes: XXX The number by “FreeKilobytes” should be 60K or greater to effectively operate the D5200.  Less than 60K could result in erratic operation of the programmer and possible corruption of panel programming. Check for corrupted handler:       Place the cursor on the panel type (8112E, 8112E1, 8112G, 8112G1, 8112G2 or 8112A) and press ENTER GROUP. Continue pressing ENTER GROUP on several levels of the program. If the message "BAD DATABASE FILE" appears, the 8112 handler is corrupted. Delete the 8112 handler immediately and use the update feature to obtain a new copy. ... View more

Connect a 9 Volt Battery across TIP (+) and RING (-) to simulate phone voltage. From the Connect Screen in RSP - Connect Via Modem. Enter (333) in the dial string and press Connect. Force the panel to Seize the Line: 2000 Series panels - Press 2 then the installer code to connect. 4412; 6412; 8112; 7000/9000 Series panels - Press CMD 43 to connect.    RPS, Remote Programming Software, RPS-LITE, D6412, D4412, D2212, D2412, D2812, D8112,RPS-LITE,US Robotics 56K External Datafax Modem, Securcomm DL 110 Modem, Hayes 2400 Optima Modem, Hayes 2400 Smart Modem, Hayes 1200 Smart Modem. ... View more

 The panel contains programming for 8 Opening Windows and 8 Closing Windows.    D7000/9000 thru GV4 series control panels contains programming for 8 Opening Windows and 8 Closing Windows.  The first opening window reports as Sked 41 and the first closing window reports as Sked 42.  These skeds log incrementally as described in the table below.   Window     Open          Close             Window     Open          Close 1                       Sked 41         Sked 42                 5                 Sked 49         Sked 50 2                       Sked 43         Sked 44                 6                 Sked 51         Sked 52 3                       Sked 45         Sked 46                 7                 Sked 53         Sked 54 4                       Sked 47         Sked 48                 8                 Sked 55         Sked 56 ... View more

Backlighting on the D623 or D625 keypad, used on D4412 and D6412 panel types is controlled by using Command 49.   Press [CMD] + [49]. Hold the star key and tap the  3 key to make the display brighter. Hold the star key and tap the  6 key to make the display dimmer. Press the Command key again to resume normal operation.   ... View more

Flash Pattern: Flash at 1x/sec rate: Normal operation. Flash at 3x/sec rate: An SDI2 communication error or the device has nothing programmed to it. Steady ON: A trouble condition exists. Steady OFF: Module is not powered or some other trouble condition prohibits the module from controlling the heartbeat LED. OFF for 3 sec, then flashes: Firmware version.  Example; if the Firmware version is 3.2.1, the LED pulses 3 times and pauses for 1 sec, pulses 2 times and pauses for 1 sec, then pulses 1 time.  After flashing the Firmware version, the heartbeat LED stays OFF for 3 sec before indicating the module state. ... View more