Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎08-16-2023 07:58 PM
    How to set and View Date and Time using the D1255 Keypad.
    View full article
    ‎07-13-2023 07:56 PM
    How to configure Swinger Shunt to prevent points from automatically bypassing after  only 1 alarm. Why does the panel zone generate 1 Alarm and then goes into Swinger Bypass? D4412,D6412,DS7220,DS7240
    View full article
    ‎07-13-2023 07:37 PM
    How to arm only the area the keypad is assigned to rather than all of the areas it can see.
    View full article
    ‎06-16-2023 09:59 PM
    How to view area status from the keypad.  
    View full article
    100% helpful (1/1)
    ‎07-12-2021 08:30 PM
    How to Exit Service Mode the B9512G/B8512G or B-Series panel. Why is the Heartbeat LED flashing fast?
    View full article
    ‎03-08-2021 11:00 PM
    Program the G-GV4 Panel to work with the D1256RB or D1256 fire keypad.
    View full article
    ‎01-08-2020 07:43 PM
    How to adjust the display on the D1260 Command Center. The The [99 + Enter “Setup?” Function] is no longer available in GV2 and higher control panels.
    View full article
    ‎08-06-2018 08:33 PM
    How to vew the History log on D7000/9000 and G series panels. D7212B,D7212B1,D9112,D9112B,D9112B1.
    View full article
    ‎08-02-2018 07:49 PM
    How to troubleshoot missing alarms on points connected to the D222A keypad. D2212, D2412, D2812, D222A.
    View full article
    ‎08-01-2018 10:56 PM
    How to determine the current draw for keypads used on the D4112 or D6112 panels. D4112, D6112, D636, D620, D626, D630, D640.
    View full article
    ‎08-01-2018 07:53 PM
    How to force arm the D4112 or D6112 control panel.
    View full article
    ‎07-31-2018 10:22 PM
    Keypad programming is available in GV3 panels with firmware revision 8.10 or higher.  NOTE: Keypad programming is not available during while an RPS programming session is active, or when any area is armed. Enter from normal operation: Press [9]+[9]+[Enter]. Select Keypad Programming. The keypad displays Enter Passcode. Enter the service passcode (default= 123). Enter from service mode (reset pin closed): D1255: Set the address to 16 with dipswitch: 1-5= OFF and 6= ON. The keypad displays Enter Passcode when the reset pin is closed. Enter the service passcode (default= 123). D1260: Set the address to 8 with dipswitch: 1-3= OFF and 4-6= ON. The keypad displays Enter Passcode when the reset pin is closed. Enter the service passcode (default= 123). The following options are available upon entering keypad programming: Phone Numbers – Phone 1 thru Phone 4 Phone Format - Phone 1 thru Phone 4 Enhanced Comm – Path 1 thru 4 Routing Route Groups 1 thru 4 RPS Parameters RPS Passcode RPS Phone Number RPS IP Address RPS IP Port Area Parameter – 1 thru 32 Account On – Yes / No Account Number Command Center 1 thru 16 Enhanced Command Center – Yes / No Command Center Scope – User Pass Code User 0 (Install Passcode) User 1 (User Passcode) Point Parameters D9412GV3: 1-247 D7412GV3: 1-75 D7212GV3 1 -40 Point Index Disable Keypad Programming
    View full article
    ‎07-30-2018 10:11 PM
    How to determine the max available current for point 1 in the D4412 or D6412.
    View full article
    ‎07-25-2018 07:21 PM
    What command centers will work with the D2112
    View full article
    ‎07-25-2018 04:00 PM
    Overview: User is entering passcode twice to arm alarm system. A five second delay between key strokes will cause the keypad to view the next entry as the start of a NEW passcode. Key strokes must be strung together with no pauses in between longer that 5 seconds. Issue User must enter passcode twice to arm the system.  Same code is used for both entries.   Solution   The user is pausing too long between key strokes.  After a key is pressed the next key stroke must be pressed wthin 5 seconds. A delay of 5 or more seconds will cause the keypad to view the next key stroke as the start of a new entry.
    View full article
    ‎07-24-2018 04:50 PM
    Where does the phone number information get entered in programming to instruct the end user to contact the security company when the help key is pressed on the D1260 keypad?
    View full article
    ‎07-19-2018 10:46 PM
    How to unbypass points on the D7112 panel.
    View full article
    100% helpful (1/1)
    ‎07-23-2018 07:52 PM
    How to dim or brighten the display on the D1255 keypad?
    View full article
    ‎07-17-2018 07:10 PM
    How to interpret 'CALL FOR SERVICE' when logging into the Easy Series panel user menu.
    View full article
    ‎07-17-2018 06:55 PM
    How to interpret the flashing amber circle on an Easy Series control panel.
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist