Bosch Building Technologies

    Showing results for 
    Search instead for 
    Did you mean: 

    How to configure time services in a BVMS version ≤ 10.1 environment?

    Time is everything: meetings, public transportation, religion, transactions: the whole world is working because the concept of “time” exists. Within a security (or any other) system this is not different: recording schedules, logging, authorizations, encryption keys, timelines, all of these concepts can exist because of time.

    As a result, time can either make or break a system: problems can appear only due to a time difference of a couple of seconds between two system components.

    This article describes how time services can be configured in a BVMS version ≤ 10.1 environment.

    For BVMS  version ≥ 11.0 please refer to the following article:

    Time: what is the challenge?

    Each device has its own internal clock, which is based on a hardware mechanism. This mechanism acts like a watch: try to put two watches together and synchronize them on the millisecond. A security system consists out of more than two devices, it can consist of thousands of devices.

    Synchronizing the time of all these devices by hand is a very time consuming task. Additionally, due to small differences in electronic components, devices can have deviations from one another.

    These deviations cannot be detected by the human eye, but can result in considerable time differences when a device is running for months.

    Synchronizing time

    The Network Time Protocol (NTP) was created to solve these challenges. The Network Time Protocol is a network-based protocol for clock synchronization between system components. The protocol utilizes a standard IP network to communicate and can maintain a time difference (considering a local area network) of less than one millisecond between components. The Network Time Protocol is a standard protocol and documented in RFC 5905.

    The operation and configuration of the Network Time Protocol are complex: a hierarchical architecture needs to be set-up including several layers of systems which are able to run the Network Time Protocol. To reduce complexity the Simple Network Time Protocol (SNTP) was  created. The Simple Network Time Protocol is mainly used when less accuracy (deviations of 1-2 seconds are acceptable).

    Windows Time Service

    The Bosch Video Management System is running on Microsoft Windows Server operating systems. Windows includes an internal time service, which is explained on Microsoft Technet:

    “The Windows Time service, also known as W32Time, synchronizes the date and time for all computers running in an AD DS domain. Time synchronization is critical for the proper operation of many Windows services and line-of-business applications. The Windows Time service uses the Network Time Protocol (NTP) to synchronize computer clocks on the network so that an accurate clock value, or time stamp, can be assigned to network validation and resource access requests. The service integrates NTP and time providers, making it a reliable and scalable time service for enterprise administrators.

    The W32Time service is not a full-featured NTP solution that meets time-sensitive application needs and is not supported by Microsoft as such. For more information, see Microsoft Knowledge Base article 939322,Support boundary to configure the Windows Time service for high-accuracy environments (

    Source: Windows Time Service Technical Reference - Microsoft Technet

    The Windows Time service is based on the Simple Network Time Protocol.


    The Network Time Protocol requires a very complex infrastructure, which impacts the total installation and configuration effort of the system. The Simple Network Time Protocol (also used for the Windows Time Service) reduces the complexity, but at the same time also reduces the accuracy.

    • For most security applications the Simple Network Time Protocol provides sufficient accuracy. Bosch recommends to use the Windows Time service, based on the Simple Network Time Protocol, as basis for time synchronization in a security network. This article provides best-practices on how to configure the Bosch Video Management System and related components in a time synchronization environment based the Windows Time service.
    • Alternatively, the Network Time Protocol can be used whenever it is already existing inside an infrastructure or when event accuracy with a deviation less than one second is required. Due to the complexity of the infrastructure Bosch does not make any recommendations related to the Network Time Protocol.



    Step-by-step guide


    Management server configuration


    A. Operating system configuration

    This section also applies for the Video Recording Manager and Mobile Video Service when these are not running on the management server.

    Microsoft has prepared a lot of documentation related to time configuration Go to the Microsoft Support: How to configure an authoritative time server in Windows Server page and scroll down to the section “Configuring the Windows Time service to use an external time source”. Click the download button under the “Here’s an easy fix” section.

    1_How to configure time services in a BVMS environment.png

    Figure: Download the Microsoft Windows Time service configuration utility


    The utility will configure external time servers. To select these, browse to and select two servers which are related to the geographical location of the system, for example “” and “”, referring to Germany and the Netherlands. Another (local or external) (S)NTP server can also be chosen.


    Start the Microsoft configuration utility and configure it as indicated and shown in the figure below.

    Administrative access is required to run the utility.

    2_How to configure time services in a BVMS environment.png

    Figure: locations


    3_How to configure time services in a BVMS environment.png

    Figure: Windows Time service configuration


    Alternatively the configuration can be done from the command-line, using the command shown below.

    net stop w32time
    w32tm /config /syncfromflags:manual /manualpeerlist:","
    net start w32time

    The configuration can be verified by starting the Windows Command prompt and issuing the command “w32tm /query / status”, as shown in the figure below. Notice the time source, this should point towards the configured servers.

    4_How to configure time services in a BVMS environment.png

    Figure: verifying configuration


    It can take up to one minute before the correct time source is displayed.

    When there is a problem, the configured (S)NTP server can be tested by issuing the “w32tm /stripchart /”, which should result in the output displayed in the figure below.

    5_How to configure time services in a BVMS environment.png

    Figure: test the (S)NTP service


    When an unexpected result is returned, it is recommended to check access to the specific (S)NTP server. A firewall might prevent the communication between the (S)NTP server and the management server.


    B. BVMS Management Server configuration

    BVMS automatically points devices to its own time-server. This can be changed by editing the BvmsCenterlServer.exe.config file, located in C:\Program Files\Bosch\VMS\bin\. Find the key "TimeServerIPAddress" and adjust the value, as shown in the example below (

    <!-- Ip address of the time server for VRM/NVR encoders(defaults to the Central-Server IP if not set). -->
    <add key="TimeServerIPAddress" value="" />


    6_How to configure time services in a BVMS environment.png


    C. Workstation configuration

    The Bosch Video Management System Operator client runs on a Windows workstation. When the workstation and server are part of the same Microsoft Active Directory service domain, no manual time synchronization needs to be configured.

    7_How to configure time services in a BVMS environment.png

    Figure: workstation configuration, "" needs to be replaced by the IP address or Fully Qualified Domain Name of the management server.


    When the Bosch Video Management System workstation and management Server are not joined in a domain, or into the same domain, the workstation(s) need to be manually configured to use the management server as a time server. To achieve this, the description above can be used. Instead of using the as a server, the management server is now entered.


    D. Camera configuration

    If a camera is connected to a BVMS system the time server will be automatically configured.

    Version history
    Last update:
    ‎08-24-2021 02:09 PM
    Updated by:
    Labels (5)