This article describes how to factory default a DIVAR IP 5000 Unit
The DIVAR IP 5000 does not come with a internal DOM for recovery, but with SSD media inside with relevant recover partition used during new recovery process.
The Reset Button is used for two options of Recovering the unit - see installation Manual page 25 - chapter 8.2. The button is located on the lower left hand side of the appliances rear connection panel. This button is utilized in both reset procedures. The following order need to be kept and the manual corrected:
Defaulting Video Recording Manager (VRM)
To default an appliances previously configured VRM, with the appliance powered on and functioning.
Press and hold the reset button for 10 seconds
Then the VRM database will be set to factory default; No recordings will be removed from the unit; And IP addressing will remain, as well as any modifications to the operating system (time settings etc.)
Factory Defaulting the Appliance
Power the appliance completely off.
Apply power, and only after LED activity is seen on the front of the appliance, press and hold the reset button.
After a few seconds an audible “beep” should be heard. This is a signal that the internal watch dog has acknowledged the reset request. Release the reset button
When the reimage process is finished the appliance will reboot. After reboot users can use the IPHelper.exe to connect to the appliance’s Configuration Wizard or use the Configuration Manager to monitor when the DIVAR IP 5000 comes back online.
... View more
Firmware The table below lists the firmware versions which are used in the BVMS 8.0 system test. Bosch Video Stitcher 184.108.40.206 VideoSDK 6.12.0078 Firmware MPEG-4 4.15.0002 Firmware CPP3 5.74.0004 Firmware CPP4 6.41.0037 Firmware CPP5 6.30.0047 Firmware CPP6 6.41.0037 Firmware CPP7 6.41.0037 Firmware CPP7.3 6.41.0037 Firmware CPP-ENC 5.53.0004 (for VIP X1600 XFM4) Firmware CPP-ENC 5.97.0005 (for VJT XF E family, VIDEOJETdecoder 3000) Firmware X1/X2 2.53.0005 VIP XD HD 1.8 VJD 7000 54.8.2 VJD 8000 9.00.0134 VRM 3.70.0056 VSG 6.42.0010 iOS 9.0.2 / 9.3.5 / 10.3.1 Web Client 11.0.96 Software The table below lists the software versions which are used in the BVMS 8.0 system test. BIS 4.3, 4.4, 4.5 DiBos 8.7 BRS 8.10/8.11 Allegiant MCS 2.94 / 2.95 Intuikey Keyboard 1.96 DVR FW Version 2.3.2 (DVR400 / 600) 3.61 (DIVAR 700) 2.5.0 (Divar AN 3000/5000) 1.2.1 (Divar Network/Hybrid) SQL Server 2014 Operating systems Operator Client Windows 8.1 64-bit; Windows 10 64-bit creators update (1703) Config Client Windows 8.1 64-bit; Windows 10 64-bit; Windows Server2012 R2 64-bit; Windows Server 2016 64-bit. Management Server, Mobile Video Service Windows Server 2008 R2 SP1 64-bit; Windows Server2012 R2 64-bit; Windows Server 2016 64-bit. Cameo SDK 220.127.116.11 BVMS SDK 18.104.22.168 RCPP 22.214.171.124 Hardware drivers NVIDIA Quadro Quadro Pro Driver for Microsoft Windows 7/8.1 (64-Bit) 385.08 (28.June 2017) Quadro Pro Driver for Microsoft Windows 10 (64-Bit) 385.69 (21.September 2017) AMD FirePro Unified Graphics Driver for Windows 8.1/10 (64- bit) 17.Q3 (27.July 2017) Bosch strongly urges customers to use the driver and software versions mentioned above. This ensures that the software can perform its task reliably.
... View more