About David

 The D1260 and D1265 are enhanced command centers which require the Enhanced Command Center parameter set to Yes. This settin can be modified from default using the below steps. Note: Keypad programming is only available on GV3 panel types with firmware version 8.10 and higher.  Keypad programming must not be disabled in the panel program settings. 1.  Use the following steps to set a D1265 command center address as Enhanced:      a. Set the D1265 to address 8 .          i. Press and hold the 0 button for at least 5 sec to access the set-up menu.          ii.  Using the up and down arrows select address 8. Press Save followed by Back to exit the set-up menu.      b. Lock down the panel reset pin, S1.      c. Enter the installer passcode followed by enter, the default code is 123.      d. Select Keypad Programming.      e. Press Next, then Next again and select the Command Center menu option.      f. Enter the address to be used by the D1265 followed with Enter.      g. The D1265 responds with CC (x)  Scope , No Device (or the currently programmed scope).      h. Press Type, will say Enhanced=No, press Edit, select Yes, then Enter.      i. Press Exit, and then Edit to edit the scope.  Press next until the correct scope displays and then Enter to save.       j. Press Exit, and follow step [a.] to set the D1265 to the required address.  2.  Use the following steps to set a D1260 command center address as Enhanced:       a. Set the D1260 to address 8 with switch setting 1,2,3 OFF and 4,5,6 to ON      b. Lock down the panel reset pin, S1.      c. Enter the installer passcode followed by enter, the default code is 123.      d. Select Keypad Programming      e. Press Next until menu item Command Center displays and select it      f. Enter the address to be used by the D1260 followed with Enter.      g. The D1260 will respond with CC (x)  Scope , No Device (or the programmed scope).      h. Press Type, will say Enhanced=No, press Edit, select Yes, then Enter.      i. Press Exit, and then Edit to edit the scope.  Press next until the correct scope displays and then Enter to save. ... View more

Use the options described below to operate and test the D2212, D2412, D2812 panel types using a D222 or D223 type keypad. Press 1 System Test Mode (Installer switch closed) Close the Installer Switch and when the keypad responds with ‘System Trouble Press 4 to View’, Press (1) to enter System Test Mode.  The keypad will respond with Enter Code to Start Test. Enter the installer code (default=654) and the following menu options will display: 1)       Bell Test 2)       Battery Test 3)       Phone Test 4)       RF Programming 5)       Point Status (Press 5 and the first two points display, press the asterisk (*) to advance to next two points.  All points will display regardless if programmed.) 6)       Relay state 7)       Menu item (7) is not used 😎       Keypad programming  Press the number corresponding with the desired menu option. Press 2 Answer RPS Press 3 Reset Sensors Press 4 Check System Troubles If system troubles are present, the keypad will respond with System Trouble Press 4 to View. Press 4 and the Call For Service text will appear.  Press and hold the 5 key and one or more of the following will appear: 1)       Low or Missing Battery 2)       Stand-By Switch Locked 3)       Aux Power Trouble 4)       Bell power Trouble 5)       Receiver # Tamper 6)       Receiver # Trouble (No Signals) 7)       Receiver # Trouble (Jammed) Press 5 Change Passcode Enter old code, enter new code, enter new code again, the keypad should respond with Code Changed. Press 6 Show Passcode Type / Add Passcode 1. Enter Owner Code to modify codes      1) Press 9 to renew one time codes      2) Press 1 to change code types- Displays current code type. Responds with: Select Code (1-8). Select code and:           1.       Select 1 for Owner           2.       Select 2 for User           3.       Select 3 for One-Time code           4.       Select 4 for Disabled      3) Press 0 to change code.  Responds with: Select Code (1-8). Enter new code. Enter new code again. 2.  Press 0 to change code.  Responds with: Select Code (1-8). Enter new code. Enter new code again Note:  Adding passcodes is controlled in panel programming.  If pressing 6 or the code entered is not allowed check the panel program setting for Change Passcode.   -  Disabled:  Passcodes cannot be changed from the keypad. -  Owner: The function requires an owner type passcode. -  Owner & User: Any owner or user passcode type may be used. Press 7 Select Watch Tone  Responds with: Enter Code to Change Tone. Select one of the following: Off Short Beep Beep Till Key Beep Till Closed Press 8 Change Watch Points  Responds with: Enter Code to Change Points. Enter Point number + * to toggle watch mode on or off for points. Press 9 All-On Press 9,9 All-On with No Delay Press 0 Part On Press 0,0 Part-On with No Delay Press /hold CLEAR key Toggle backlighting ‘Always Illuminate’  / ‘Illuminate with keypress’ ... View more

The D4412 and D6412 use the D621, D623 or D625 command centers. Pressing All-On or Part-On on the will arm only the area where the keypad is assigned. Command 50 may be used to move to an area other than the programmed assigned area.  After moving to the selected area, press either All-on or Part-on to arm the area. Command 80 may be used to arm all areas. Command 81 may be used to disarm all areas. Note:  Commands 80 and/or 81 must be enabled by an individual with assigned authorization to perform the function. Use Command 50 to move to another area and arm:  Press [CMD] [5][0] and enter a valid code if required. The keypad will scroll through all available areas. Press the desired area number to move to the area.  Press All-On or Part-On to arm the selected area.  Pressing and holding [CMD] will exit the Command 50 feature returning the keypad to its “home” area. Use Command 80 to arm All Areas: Press [CMD] [8][0] and enter a valid code if required.       Hold down the All On key for 2 sec and it forces all areas to All On.  Use Command 81 to disarm All Areas:  Press [CMD] [8][1] and enter a valid code if required. The keypad will indicate all areas are off. ... View more

EN1210W and ISW-EN1210W Inovonics wireless transmitters have an internal reed switch.  In additon to satisfying the external contacts, the reed switch must be satisfied with a magnet to before the point can restore to normal. ... View more

Custom functions can be programmed into a command center through a series of key presses . The specific sequence of key presses varies with the type of command center running the custom function. Most commands performed on the D1260 Enhanced Command Center utilize “soft keys”. These “soft keys”, located on the left and right side of a large LCD display, are used in most commands performed on the D1260. Therefore the sequence of pre-programmed key presses on the D1260 is different than those performed on the D1255. The D1260 Enhanced Command Center has 8 “Soft-Keys”, 4 on each side of a four-line by 20-character LCD Display. The keys are identified in figure 1 below. ... View more