Fire

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M,FPP-RNAC-8A-4C, DS9484, DS9488, D7035

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, D8125MUX, D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G, B600, B299, D8125, FPA-1000, FPA-1000-V2, FPE-7039, D7039, DS9431, FDP-7024, D7024, DS9400, DS9400I, DS8400M, D10024A, D10024, D9024, D8024, D7212B, D9112B, D7212B1, D9112B1, D7212, DS7430, DS7436,

This article provides instructions for exporting and saving the program from an FPA-1000 to be imported into a replacement FPA-1000 panel. This information may be needed when replacing an FPA-1000 fire panel with another with intentions to use the same panel program.

Part numbers DS240, DS241, D296, DD297

Question   Do Bosch addressable smokes and smoke bases support CleanMe functions?   Answer   Currently the only Bosch smoke detector that supports CleanMe functions is the F220 series smoke heads when used with a conventional two-wire (F220-B6) base only and a CleanMe enabled control panel such as the D7024, and FPD-7024 conventional zones. Note:  The D7050, D7050TH does have a Chamber Check feature that will report dirty smoke if the head needs cleaning when used on the D7024, FPD-7024, DS9400m, DS9400, DS9400i.

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9431, D7039, FPE-7039

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M,

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M,D7039, DS9431

Part numbers FMM7045, FMM7045-D, D7024, FPD-7024, DS9400, DS9400I, DS9400M,

Part numbers F220-P, D285, D263, D273, D273ES, D263TH, D263THS, D263THC, D273THR, D273THSR, D273THC, D273THCS, D273THE, D273THS, D273TH, D273IS, F220, F220-PTH, F220-PTHC

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

How to configure the FPD-7024 to communicate by phone using keypad programming. How to use keypad programming to configure the FPD-7024 for phone communications.

This feature blocks the programming feature through the keypad of the FPD-7024. This feature is only enabled via RPS.   Step-by-step guide   1 Connect to the Panel via RPS an Open the FPD-7024 programming sheet.   2 Go into Program Accounts and Remote Access Security.   3 Open Anti-takeover Setting and Select "Lock all local programming (except Date/Time and all user PINs)" to block the programming via keypad of the panel.  

Can the installer code be returned to default in the FPD-7024, D7024, DS9400, DS9400I, DS9400M fire panels?  

Part numbers D7024, FPD-7024, D7042, D7052, D7053

Part numbers D7033, FMR-7033, DS9447

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part numbers FPP-RNAC-8A-4C, D7038, DS9484,

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, D7034, FPE-7034, DS9434