Fire

Use the program menu tree shown below to program D9068 using the FMR-DACT-KEYPAD or D7033 Programming Keypad.    

Part numbers - FPA-1000, FPA-1000-UL, FPA-1000-V2, FLM-325-CZM4

Part Numbers FPA-1000, FPA-1000-UL, FPA-1000-V2, FPE-1000-SLC

Part Numbers FPA-1000, FPA-1000-UL, FPA-1000-V2, FLM-325-IM, FLM-325-I24, FLM-325-I24-A, FLM-325A, FLM-325, FLM-325A-D,

Part Numbers - D7024, FPD-7024, DS9400, DS9400I, DS9400M

Bosch part numbers D340, DS290, D263, D263TH, D263THC, D263THS, DS282, DS282TH, DS282THC, DS282THS, F220-B6, F220-P, D287, D288, D285, D285DH

Part Numbers D7024, FPD-7024, DS9400, DS9400I, DS9400M

Part Numbers D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, D192C, D192G

Part Numbers D10024, D10024A, D9024 ,D8024, D326 ,D326A, D334 ,D334A, D339, D339A  

Part Numbers D9068 (DACT Dialer), D9052 (Interface Module for Serial DACT Connect to the Morley Panel), D10024A, D10024, D9024, D8024 (Morley Fire Panels), D7033 and FMR-DACT-KEYPAD (Keypad Programmer for the D9068

The FAA-325-B6S is to be used with the FAP-325, FAI-325 and FAH-325 model sensors only. The FAA-325-B6S provides an audible alarm in the immediate vicinity. Typical applications are for use in hotels, apartments, and hospitals. It is compatible with the FPA-1000, FPA-1000-UL, and FPA-1000-V2.

FPD-7024, D7039

High Voltage (HVLT) Green - Warns of dangerous voltages when lit. Output Active (OUT) Red - Indicates that one of the NACs (1 to 4) is active. NAC Short (SHRT) Yellow - Indicates that there is a short on one of the four NAC outputs. Low Battery (LBAT) Yellow - Indicates that there is a missing or dead battery. AC OK (ACOK) Green - Indicates that the input is good and that the power supply is running from the AC line. Ground Fault (GFLT) Yellow - Indicates that the NAC output wiring has been improperly connected to an external source or ground. Loop Trouble (TBL) Yellow - Indicates that one, or both, NAC Input EOL device(s) has disconnected due to one or more of the following faults: Faulty AC power (after a delay) Low battery fault Ground fault NAC output fault EOL shorted EOL open NAC overcurrent Power supply over voltage condition

D7038, DS9484

Part number list, DS9400, DS9400I, DS9400m, D7024, FPD-7024, D7053, D7035, D7039, FPE-7039,DS9431, DS9431R, MX465, DS9465, DS9465I, DS9432.

FPA-1000, FPA-100-UL and FPA-1000-V2 - does not send restoral reports for events requiring a reset. The Reset Report is the Restoral.

Uses for the  D298M over a D298S or D278S popited base? D278S 12 volt popit base. D298S 24 volt popit base. The D298M is a 24 volt popit base that provides connections for up to 19 supervised circuits two-wire slave detectors (D287 2-Wire Base with D285 Smoke Head or D285TH Smoke Head with 135 degree heat sensor) reporting to the master address. The D298M is used over the D298S to conserve popit addresses on a large system.

Part Numbers of old Morley Fire Panels -  D10024, D10024A, D9024, D8024. Part Number of the Loop Card (SLC Card) D9067.

The D305 does not have the ability to trip the control panel or smoke head into alarm. The D305 Test Plate only toggles the alarm LED and relays of the D332A, FAD-325-R and FAD-325-V2F-R. The only way to get the control panel to display an alarm or supervisory  from the Analog Hochiki DUCT Detectors is by using UL Listed canned smoke (refer to the testing procedure below). Currently the only work-around is to connect a single point module (D334A, D339A, FLM-325-IM, FLM-325-I4, FLM-325-I4-A or FLM-325-I4-AI) to one of the alarm relays of the D332A, FAD-325-R or FAD-325-V2F-R. *Note: If the customer installed the D331A, FAD-325, or FAD-325- V2F we have no way of using the D305 to trip the panel into alarm.  Option 2 - Replace the DUCT Housing (D331A, D332A, FAD-325, FAD-325-R, FAD-325- V2, or FAD-325- V2-R) and Test Plates (D305) with D341P Conventional DUCT Housing with Head, D344-RT Remote Test Plate, and D339A, D334A, FLM-325-IM, FLM-325-I4, FLM-325-I4-A or FLM-325-I4-AI Analog Single Point Monitor Module. The downside is that the customer will lose the ability to read the sensitivity of the DUCT through the control panel web-browser. Testing  Procedure (D331A, D332A, FAD-325, FAD-325-R, FAD-325- V2, or FAD-325- V2-R) Install the detector housing. The green Pilot LED on the housing’s front lights. Remove the head. The Pilot LED goes out to indicate head supervision. Replace the head and reset the FACP. Test the detector’s operation. Light a piece of clothesline and place it approximately 3 in. (7.6 cm) from the head. Blow across the lighted area toward the detector head. The Alarm LED lights within 1 min and the two alarm relays energize shorting Terminal 8 to 9 and Terminal 11 to 12. Reset the housing. The detector momentarily resets and returns to the alarm condition. Perform this operation several times. After 5 min, the smoke in the detector head clears and the detector remains reset. Replace the cover. 

Listed in the table below you will find the old DS MUX Device part number with the new MUX Device replacement. Replacement Part Numbers Old DS MUX Devices Description FPE-7039, D7039 DS9331, DS9431R MUX Card D7050-B6 MXB2W MUX Base D7044 MX361 Single Point D7044M MX361M Mini Single Point FMM-7045 MX310 Pull Station FMM-7045D MX310D Dual Action Pull Station D7052 MX363 Dual Point Module D7053 MX46 I/O Input/Output Modules D7050 MX250 MUX Smoke Head D7050TH MX250TH MUX Smoke Head with 135 Heat Sensor  .