Fire

Mux Card replacement (DS9431, DS9431R, D7039, or FPE-7039) on any of the following panels DS9400, DS9400I, DS9400M, D7024, and FPD-7024.

Perform these steps to enable the D7024, FPD-7024, DS9400, DS9400I, and DS9400M for RPS programming via phone line with a compatible RPS modem: Press (0) Enter Program Mode. Enter Pin (Default is 9876). Press (6) Accounts. Press (4) Ring Count. Set Ring Count to (02) #. Press the (*) key two times or until you see PROGRAM MODES. Press (3) System. Press (7) Remote Program. Press (1) Enable. Press the (*) key five times to Exit Program Mode. You need to dial Line 1 on the panel. It is the second line down on the panel (it is NOT the line in the top right). Before connecting with RPS, perform an Auto-Learn with at least one Mux Device connected to the Mux loop, then send your RPS program to the panel. Press (0) Enter Program Mode. Enter Pin (default is 9876). Press (9) Program Mux. Press (4) Auto Program. Press (1) Yes.

The FPA-1000, FAP-1000-UL and FPA-1000-V2 all have the option to use 2 FPE-1000-SLC Loop cards. Each loop card on panel with Firmware less then 1.09 only support address 1 to 127 on each loop card, from firmware 1.10 and higher each loop card supports address 1 to 254. So it is possible to have to devices with the same address but on different loop cards. The the panel the keypad will display the following on the top line. The Event Type (Trouble, Fire, Supervisory) follow by XX-Y-AAA.A, (XX = Panel ID) (Y = Address Assignment, 0 - Web Page, 1 - SLC1, 2 - SLC2, Mainboard, or 4 - Option Bus) Followed (AAA.A The Device Address) .

Part Numbers for Flush Mount Smokes - FPC-500, FCP-500-C, FCP-500-P, FAA-500-BB-UL, FCA-500, FAA-500-TR-P, FSP-500, FCA-500-E, FAA-500-TR-W, and FCP-500-C-P. To make ordering easier please refer to the Product Data-Sheet and order the kit part numbers.

Related Products Part Numbers D380, Macurco CM15/15A

Panel part numbers - FPD-7024, FPA-1000, FPA-1000-UL, and FPA-1000-V2. Network Card part numbers for the FPD-7024, DX4020, B420, and B426. Cellular option for the FPD-7024 part numbers B450 (Interface for Cellular Card) B440, B441, B442, B443, and B444.

AC Fail operation in the following panels. D7212GV2, D7412GV2, D9412GV2, 7212GV3, D7412GV3, D9412GV3, 7212GV4, D7412GV4, D9412GV4, B8512G and B9512G.

How to upgrade the D5070 Programmer to program addresses 128 through 254.

Only one keypad can be used at a time on the FPD-7024. Your keypad options are the builtin keypad on the FPD-7024, the FMR-7033, or the FMR-7036.

DS9400, DS9400M, D7024, and FPD-7024 Fire Alarm Panels the Water-Flow timer operation.

Testing DACT phone lines.

One of the following programming keypads (FMR-DACT-KEYPAD, D7033, or DS9447) displays "SYSTEM FAULT" when programming one of  the following DACT models: D9068, DS9602, DCT-1, DCT-1E or FPT-DACT.

Perform a sesitivity test on the following MUX smoke heads, D7050, D7050TH, D7050DH, MX250, MX250TH & MX250DH.

The point Index is set to (0), yet the point still displays in trouble at the keypad and as Extra Point in the panel History Log. How to correct this senario.

Configuring the FPP-RNAC-8A-4C on an Option Bus Fire panels FPD-7024 & FPA-1000.

AC Fail or Low Power Trouble on FPP-RNAC-8A-4C

D125X Keypad is not displaying System Faults

This article discusses how to send reports to the CS (Central Monitoring Station) from the FPA-1000-V2. We can network up to 8 of the FPA-1000-V2 panels together.  Each panel can report to the CS by itself, or one panel can report for all.  In either configuration, each panel needs its own unique account number.  

Steps to enable a SLC card in slot 2

How to test the D382 or Macurco GD-2A Combustible Gas Detector