About David

WDSRP software waspreviously used to program the panel.  The account was protected from takeover by limiting parts of programming from the keypad. WDSRP remote programming software provides options to limit all or parts of keypad programming in the Remote Access area of the account.   Select Edit Remote Access and the below dialog box appears. Select the desired option in the bottom right-hand corner of the dialog box: All keypad programming is allowed. Can't change phone numbers.Programming addresses to edit phone numbers is blocked. No keypad programming is allowed. No access to programming through keypads is allowed.   Note that the WDSRP software is no longer available or supported.  When not readily available, the panel must be replaced. ... View more

Check the "JP1" jumper located on the right edge of the DS7400 board. If the "JP1" jumper is cut, a 27K EOL is required to terminate zone 8 on the panel. Zone 8 can be configured to eliminate ground fault detection by cutting the jumper wire "JP1" on the control panel. This can be done to permit use of the Ademco AB-12 Bell/Housing, which will generate a ground fault on the DS7400 zone in a normal configuration. When the jumper wire "JP1" on the control panel is cut, zone 8 must be terminated with a 27K ohm EOL. When the jumper wire "JP1" is not cut, zone 8 must be terminated with a 2.2K ohm EOL. DS7400, DS7400X, DS7400i, DS7400Xi, DS7400Xi v3+, DS7400Xi v4+ ... View more

EN5040-T or ISW-EN5040-T LED Indications: RECEIVE- Flashes when the EN5040-T or ISW-EN5040-T receives any recognizable RF transmission. TRANSMIT- Lit steady when the EN5040-T or ISW-EN5040-T transmits an RF transmission. LOW BATT- Lit steady when the EN5040-T or ISW-EN5040-T has a low battery. POWER- Lit steady Green when the EN5040-T or ISW-EN5040-T receives AC input power. Lit steady Red when receiving back-up battery power. The Power LED will light steady Red when running on back-up battery due to the loss of AC input power.  The EN5040-T or ISW-EN5040-T will send RF Low Battery signal to the ISW-D8125CW-V2 for any of the following conditions: Re-transmitting the RF Low Battery signal from a wireless transmitter. Low internal back-up battery in the EN5040-T or ISW-EN5040-T Loss of AC input to the EN5040-T or ISW-EN5040-T   The Power LED indicates power input to the EN5040-T or ISW-EN5040-T: Solid Green: AC is available. Solid Red: AC Loss; running on back-up Battery. ... View more

 The D1255RB, D1256RB and D1257RB command centers are compatible with G-Series control panels with firmware revision 7.04 or higher. When connected to earlier revision panels, the keypad basic functions will operate correctly but LED's for Fire, Silenced, Supervisory and Trouble will not operate correctly. Additionally, the D1255RB, D1256RB and D1257RB keypads are not UL listed with control panels prior to revision 7.04. ... View more

The existing Popit dipswitch address can be used with the upgraded panel-programming program by converting the D8112 address to the G-Series address. Note: The D8125 needs to have a date code higher than 9434, and D8127* Popits need to have a date code higher than 9344. Replace all D8126 Popits with D9127 Popits. D8127 Popits are not tested or not listed and therefore not recommended with GV4 and newer panel types. Replace with D9127 Popits. D8127 Popit do not have a Zero Dipswitch. When there is no 0 dipswitch, the panel will interpret the 0 switch as turned on. In cases where a D8127 popit will be used the addresses with the 0 switch turned off are not available.  In order to use these conversion tables with the B8512G and B9512G types, a B600 must be used.   ... View more