About CPrince

Issue Extend Closing, COMMAND 51.   Solution   Extend Closing COMMAND 51 Your system may be programmed to expect you to arm within a scheduled closing window, which is a duration of time that is programmed by your alarm company. Your system may also be programmed to automatically arm at the end of the window. COMMAND 51 lets you extend the scheduled closing window time either prior to the closing window time or during the closing window time. Use this function when you expect to stay past the scheduled end of the closing window. The length of time prior to the start of the closing window in which you are allowed to extend the closing window is set by your alarm company. AREA X INACTIVE displays during the time when the command center won't allow the window to be extended. At the beginning of the closing window, the command center beeps and displays PLEASE CLOSE NOW to remind you to arm your system. It remains in the display until you arm, the close window ends, or you extend closing. Alarm or trouble messages replace this message in the event of an alarm or trouble condition. If the alarm or trouble condition clears before the end of the close window PLEASE CLOSE NOW returns to the command center display. Pressing the ESC key will silence the beep and clear the message for 10 minutes. If you have not armed or extended closing, the PLEASE CLOSE NOW and beep will reappear after 10 minutes. The length of time for the closing window is set by your alarm company. To extend the window, enter the new time at which you would like the reminder tone to begin. This time will be the new beginning of the closing window. The time length of the closing window is programmed by your security company and remains fixed. When you hear the warning you can: • Leave before the end of the closing window by pressing ESC to silence the signal, arming the system, and leaving. • Stay past the scheduled end of the closing window, by using COMMAND 51 to extend the closing window. Note: The amount of time available to close is not effected by extending the closing window. For example, if your closing window starts at 4:00 p.m. and stops at 4:30 p.m. and you extend closing to 5:00 p.m., the closing window will now be between 5:00 and 5:30 p.m. 1. Ensure that your command center is at disarmed idle text. 2. Press the COMMAND bar. The display shows SYSTEM COMMAND. 3. Press the 5 key, followed by the 1 key. Note: If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function. Press the MENU key to enter the Command Menu, then press NEXT repeatedly until you reach the EXTEND CLOSING ? prompt. Press ENT. 4. The display shows CLOSE BY ##:## (##:## = scheduled start of the closing window). Enter the time you want the window to start and press ENT. Note: The window time cannot be extended across the midnight boundary. 5. AM ? displays. • If you wish to choose AM, press ENT. • If you wish to choose PM, press NEXT to display PM ? Press ENT. 6. The new “close by” time displays. Press ENT to confirm and set the new time. The time is shown momentarily before the display returns to idle text. Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G ... View more

Overview: Ram Dump Procedure for the D8112 CPU board. The D8112 is made up od a D8107 Mother Board and a D8105 CPU Card. The CPU Card is hot swappable. Issue Installing a used CPU with unknown programming.   Solution   It is possible to clear memory of the CPU Card. Procudure : *NOTE: This should be done with the CPU off the panel. With the CPU removed off the panel, remove the shroud, find CR2 and U8 on the circuit board. Place a 3 sec short across the banded end of CR2 and the center pin of U8. This will erase ALL Ram memory. Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2, D8105E, D8105E1, D8105G, D8105G1, D8105G2, D8105A ... View more

Issue What is CMD 53 - DEL PASSCODES ? COMMAND 53   Solution   DEL PASSCODES ? COMMAND 53 • Use this function to delete a personal passcode from your system without assistance from your security company. You need to know the user number for the passcode you want to delete. • The two digit user numbers identify users in reports transmitted from your system. Using Del Passcodes: 1. Ensure your command center is at idle text. 2. Press the COMMAND bar. The display shows SYSTEM COMMAND. 3. Press the 5 key, then press the 3 key. Note: If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function. Press the MENU key to enter the Command Menu, then press NEXT repeatedly until you reach the DEL PASSCODES ? prompt. Press ENT. 4. The command center displays ENTER USER NUM. Enter the two-digit user number, not the passcode. Press ENT. If you enter a user number not programmed into the system, NOT IN USE displays. Check the user number and enter again. 5. DELETE USER ## ? displays. Press ENT to delete the passcode for this user. 6. The command center briefly displays PASSCODE DELETED and then returns to idle disarmed text. Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G ... View more

Issue How do I use CHG SKEDS ? COMMAND 52?   Solution   CHG SKEDS ? COMMAND 52 • A Sked is a function programmed to be performed automatically at a scheduled time by your security system. You can change the scheduled time for some functions, disable the Sked and thus prevent it from automatically happening or restart a previously disabled Sked. Contact your security representative to determine what Skeds may be programmed for your system. Using Chg Skeds: • To change a Sked’s time, enable a Sked, or disable a Sked, follow the procedure below to first select the Sked from a list of Skeds programmed for your system. 1. Ensure your command center is at idle text. 2. Press the COMMAND bar. The display shows SYSTEM COMMAND. 3. Press the 5 key, then press the 2 key. Note: If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function. Press the MENU key to enter the Command Menu, then press NEXT repeatedly until you reach the CHG SKEDS ? prompt. Press ENT. 4. The number of the first Sked programmed into your system is displayed, plus either its time or an indication that it is disabled. Press NEXT to scroll through the list of Sked numbers to find the one you wish to change. When an X appears in the Sked display, it is an indication that “Except on Holidays” is enabled, S ## X ##:##AM. When an * appears in the Sked display, it is an indication that the Sked has or will happen today, S ## * X ##:##AM. To change the state of the displayed Sked from enabled or disabled: 1 . With the selected Sked displayed, press ENT. 2. If the Sked is currently enabled, DISABLE ? is displayed. Press ENT. The Sked displays showing it is disabled. 3. If the Sked is currently disabled, ENABLE ? is displayed. Press ENT. The display shows XOH ON ? You can toggle between this display and XOH OFF ? by pressing NEXT. To enable the Sked on holidays, press ENT with XOH OFF ? displayed. To disable the Sked on holidays, press ENT with XOH ON ? displayed. Enter the desired time and press ENT. AM ? displays, to choose AM, press ENT. To choose PM, press NEXT, to display PM ?. Press ENT. The display shows the Sked with its new time. 4. Press ESC to return to idle text. Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G ... View more

Issue How many on-board zones does the D6112 Control Communicator have?   Solution   The D6112 Control communicator has eight end-of-line resistor supervised hardwire protective zones. There are six standard programmable zones; one nominal 12 VDC powered zone optimized for two-wire smoke detectors and one nominal 12 VDC powered zone optimized for two-wire glass-break detectors. ... View more