Fire

Part Numbers, FAD-325 (DUCT Housing without Relay), FAD-325-V2F (DUCT Housing without Relay), FAD-325-R (DUCT Housing with Relay), FAD-325-V2F-R (DUCT Housing with Relay) FML-325-2R4, FML-325-2R4-2A, FML-325-2R4-2AI, FML-325-2R4-8A, FML-325-2R4-8AI, D323DH (DUCT Smoke Head), FAD-325-DH (DUCT Smoke Head), FAD-325-V2F-DH, FPA-1000, FPA-1000-UL, and  FPA-1000-V2.

Part numbers, D344-RT (Remote Test Plate with Blue Test coil), D307 (Remote Test Plate), D341, D341P, D342, and D342P. How to correct the D344-RT not resetting the D341/D342 duct detector.

Perform these steps to enable the D7024, FPD-7024, DS9400, DS9400I, and DS9400M for RPS programming via phone line with a compatible RPS modem: Press (0) Enter Program Mode. Enter Pin (Default is 9876). Press (6) Accounts. Press (4) Ring Count. Set Ring Count to (02) #. Press the (*) key two times or until you see PROGRAM MODES. Press (3) System. Press (7) Remote Program. Press (1) Enable. Press the (*) key five times to Exit Program Mode. You need to dial Line 1 on the panel. It is the second line down on the panel (it is NOT the line in the top right). Before connecting with RPS, perform an Auto-Learn with at least one Mux Device connected to the Mux loop, then send your RPS program to the panel. Press (0) Enter Program Mode. Enter Pin (default is 9876). Press (9) Program Mux. Press (4) Auto Program. Press (1) Yes.

Mux Card replacement (DS9431, DS9431R, D7039, or FPE-7039) on any of the following panels DS9400, DS9400I, DS9400M, D7024, and FPD-7024.

Listed in the table below you will find the old DS MUX Device part number with the new MUX Device replacement. Replacement Part Numbers Old DS MUX Devices Description FPE-7039, D7039 DS9331, DS9431R MUX Card D7050-B6 MXB2W MUX Base D7044 MX361 Single Point D7044M MX361M Mini Single Point FMM-7045 MX310 Pull Station FMM-7045D MX310D Dual Action Pull Station D7052 MX363 Dual Point Module D7053 MX46 I/O Input/Output Modules D7050 MX250 MUX Smoke Head D7050TH MX250TH MUX Smoke Head with 135 Heat Sensor  .

The FAA-325-B6S is to be used with the FAP-325, FAI-325 and FAH-325 model sensors only. The FAA-325-B6S provides an audible alarm in the immediate vicinity. Typical applications are for use in hotels, apartments, and hospitals. It is compatible with the FPA-1000, FPA-1000-UL, and FPA-1000-V2.

Morley Fire Panels D8024, D9024, D10024, and D10024A. Obsolete Morley printer module D9050. Panel replacement FPA-1000, FPA-1000-UL and FPA-1000-V2.

*Note: DS9431 MUX was replaced by the D7039, The D7039 was replaced by the FPE-7039

DACT Dialers - D9068, FPT-DACT, FPT-DACT-232, DCT-1, DCT-1E, DS9602 Keypad Programmers - FMR-DACT-KEYPAD, DS9447, D7033, DCT-P

Replacement part for the D328 and D328A Relay Module on a D8024, D9024, D10024 or D10024A FACP is obsolete with no replacement availible for the older Radionics / Morley panels.  

Option Bus NAC Outputs (FPP-RNAC-8A-4C) will never be in sync with the NAC Output of the panel (FPA-1000, FPA-1000-UL, FPA-1000-V2, or FPD-7024).

How to upgrade the D5070 Programmer to program addresses 128 through 254.

Only one keypad can be used at a time on the FPD-7024. Your keypad options are the builtin keypad on the FPD-7024, the FMR-7033, or the FMR-7036.

Products: B8512G, B9512G, B925F, B926F

Perform a sesitivity test on the following MUX smoke heads, D7050, D7050TH, D7050DH, MX250, MX250TH & MX250DH.

How to configure the FPD-7024 for various network reporting options. How does the FPD-7024 Network Communication alternate between devices?

How to access the Menu features on the B926F which does not have a Menu button.

D125X Keypad is not displaying System Faults

Part numbers FPA-1000, FPA-1000-V2, FPE-1000-NE, FPE-1000-NW, FPR-1000-NF  

Steps to enable a SLC card in slot 2