Fire

Part numbers D8125, D8126, D8127, D9127, D9127U, D9127T

Part numbers D10024A, D10024, D9024, D8024

Overview When the D928 is installed, the control panel alternates between Phone Line 1 and Phone Line 2 to send its first report. For example, on Day 1, the control panel attempts to communicate on Phone Line 1. On Day 2, the control panel switches and attempts to communicate on Phone Line 2. When the control panel is reset or powered on or off, the next reported event always attempts to call out on Phone Line 1 first. If Phone Line 2 (secondary) is not in service on Day 2, the control panel switches to the primary phone line to send the report.The Bosch Security System control panels use the D928 Dual Phone Line Switcher to transmit over a second phone line when the primary phone line has a fault. The control panel monitors the primary line and the D928 monitors the secondary line. If a signal is generated and the control panel senses that the primary phone line is bad, it will attempt to use the secondary phone line to send the message. Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, D928,

DACT Dialers - D9068, FPT-DACT, FPT-DACT-232, DCT-1, DCT-1E, DS9602 Keypad Programmers - FMR-DACT-KEYPAD, DS9447, D7033, DCT-P

How to Connect to a FPD-7024 locally using Enhanced Direct with a DX4010V2

Part numbers D1255, D1257, D1256, D1255RB, D1256RB, D1257RB, D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4,

How to configure the FPD-7024 for various network reporting options. How does the FPD-7024 Network Communication alternate between devices?

Part numbers D10024A, D10024, D9024, D8024

Part number D1255, D1256, D7412, D9412, D7212, D7412, D9112, D7212b, D7212B1. D9112B, D9112B1

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G, FPD-7024, D7024, DS9400, DS9400I, DS9400M, D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2, B465

How to test the D382 or Macurco GD-2A Combustible Gas Detector

Part numbers DS9445A-S8, DS9484, DS9431 ,DS9400i, DS9400M, DS9431R, DS9432 DS9434, DS9436, DS9441, DS9445A, DS9446, DS9447,  DS9457, DS9460, DS9465, DS9488, DS9489, DS9490, MX310, MX310D, MX361, MX361M, MX363, MX465, MX250, DS293, DS9432B, DS9445A-S2

Products: B8512G, B9512G, B925F, B926F

Part numbers D9412GV4, D7412GV4, D9412GV3, D7412GV3, D7212GV3, D9412GV2, D9124GV2,D7412GV2, D7212GV2, D9412G, D9124G, D7412G, D7212G, D9412, D9124, D9112, D7412, D7212, D192C, D192G

The DataLock system uses lockcodes to lock panels from programming by unauthorized programmers. A Datalocked panel has a lockcode in memory that the 5200 must match to one of the lockcodes in the 5200 lockcode records before the programming session can continue. If 5200 cannot match the lockcode in the panel, the programming session is terminated.

Part numbers D7024, DS9400, DS9400I, DS9400M, D7039, DS9431, FPE-7039

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9434, D7034, FPE-7034

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, D1256, D1256RB (GV2 and Higher panels)

Listed in the table below you will find the old DS MUX Device part number with the new MUX Device replacement. Replacement Part Numbers Old DS MUX Devices Description FPE-7039, D7039 DS9331, DS9431R MUX Card D7050-B6 MXB2W MUX Base D7044 MX361 Single Point D7044M MX361M Mini Single Point FMM-7045 MX310 Pull Station FMM-7045D MX310D Dual Action Pull Station D7052 MX363 Dual Point Module D7053 MX46 I/O Input/Output Modules D7050 MX250 MUX Smoke Head D7050TH MX250TH MUX Smoke Head with 135 Heat Sensor  .

Option Bus NAC Outputs (FPP-RNAC-8A-4C) will never be in sync with the NAC Output of the panel (FPA-1000, FPA-1000-UL, FPA-1000-V2, or FPD-7024).