Fire

Part numbers D7038, DS9484

The D9124 is a 9000 control panel with a 24Vdc PSU and all the needed Fire Accessories for a basic system, all in one large red enclosure. See parts List below. The D9124 is made up of the following: D9112LTB, D9412LTB ,D9412GLTB, D9412GV2LTB - Control Panel D9101 - Red Enclosure D9100 - Carriers Module with the Following parts * * 2 - D192C - Bell Supervision Modules * 1 - D8125 - Popex Module * 1 - D928 - Dual Phone line Switcher * 1 - D9142LC - 24Vdc Power Supply D1256 - Fire Keypad D1601 - Hardwire Transformer

Part numbers D10024A, D10024, D9024, D8024

Part numbers DS9400, DS9400i, DS9400M, D7024, FPD-7024, DS9431, D7039, FPE-7039

Part numbers D7038, D7024

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4

Part numbers D10024A, D10024, D9024, D8024

Issue What is the part number for the weatherproof pull station? Solution Part number for the weatherproof pull station: FMM-100SATK - This is the pull station FMM-100WPBB-R - This is the back box for it * Need both parts above to make the pull station weatherproof. The pull station (FMM-100SATK) will not be weather proof without the back box (FMM-100WPBB-R). Part numbers D467, FMM-100WPBB-R, FMR-100SATK

Part number list, DS9400, DS9400I, DS9400m, D7024, FPD-7024, D7053, D7035, D7039, FPE-7039,DS9431, DS9431R, MX465, DS9465, DS9465I, DS9432.

The D305 does not have the ability to trip the control panel or smoke head into alarm. The D305 Test Plate only toggles the alarm LED and relays of the D332A, FAD-325-R and FAD-325-V2F-R. The only way to get the control panel to display an alarm or supervisory  from the Analog Hochiki DUCT Detectors is by using UL Listed canned smoke (refer to the testing procedure below). Currently the only work-around is to connect a single point module (D334A, D339A, FLM-325-IM, FLM-325-I4, FLM-325-I4-A or FLM-325-I4-AI) to one of the alarm relays of the D332A, FAD-325-R or FAD-325-V2F-R. *Note: If the customer installed the D331A, FAD-325, or FAD-325- V2F we have no way of using the D305 to trip the panel into alarm.  Option 2 - Replace the DUCT Housing (D331A, D332A, FAD-325, FAD-325-R, FAD-325- V2, or FAD-325- V2-R) and Test Plates (D305) with D341P Conventional DUCT Housing with Head, D344-RT Remote Test Plate, and D339A, D334A, FLM-325-IM, FLM-325-I4, FLM-325-I4-A or FLM-325-I4-AI Analog Single Point Monitor Module. The downside is that the customer will lose the ability to read the sensitivity of the DUCT through the control panel web-browser. Testing  Procedure (D331A, D332A, FAD-325, FAD-325-R, FAD-325- V2, or FAD-325- V2-R) Install the detector housing. The green Pilot LED on the housing’s front lights. Remove the head. The Pilot LED goes out to indicate head supervision. Replace the head and reset the FACP. Test the detector’s operation. Light a piece of clothesline and place it approximately 3 in. (7.6 cm) from the head. Blow across the lighted area toward the detector head. The Alarm LED lights within 1 min and the two alarm relays energize shorting Terminal 8 to 9 and Terminal 11 to 12. Reset the housing. The detector momentarily resets and returns to the alarm condition. Perform this operation several times. After 5 min, the smoke in the detector head clears and the detector remains reset. Replace the cover. 

Part numbers D10024A, D10024, D9024, D8024

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412,

Part numbers 5601P, 5602, 5603, 5604, 5621, 5622, 5623, 5624

FPD-7024, D7039

Part numbers D9127, D9127T, D9127U, D9127T/U

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4, DS7420I

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, D720

Part Numbers D10024, D10024A, D9024 ,D8024, D326 ,D326A, D334 ,D334A, D339, D339A  

Part Numbers FPA-1000, FPA-1000-UL, FPA-1000-V2, FLM-325-IM, FLM-325-I24, FLM-325-I24-A, FLM-325A, FLM-325, FLM-325A-D,