Fire

Overview When devices are connected to the Option Bus on the FPD-7024, the bus must be scanned allowing the panel to see the device. After removing devices, such as the DX4020, DX4010V2 or DX4010i, the option bus must be scanned again to complete the removal, or the panel continues to supervise the device resulting in a keypad display: Trouble DX4020 and history event: SYSTRB017. Issue After completing programming the panel reports trouble DX4020; history shows SYSTRB017 Solution After removing the DX4020, DX4010V2 or DX4010i, the option bus must be scanned again to complete the removal or the panel continues to supervise the device.  From the Panel Keypad (not a remote keypad) perform the following steps to update the option bus: Select 0 for PROGRAMMING and enter the installer code Select 3 for PROGRAM SYSTEM Select 4 for OPTION BUS Select 1 for UPDATE BUS

D125X Keypad is not displaying System Faults

This article contains the RCP+ CGI commands for AVIOTEC starlight 8000 that helps you to enable or disable the scene quality (bright or dark)

This article contains the RCP+ CGI command for AVIOTEC starlight 8000 that helps you to adjust the VCA darkness or brightness level

Part numbers FPA-1000, FPA-1000-V2, FPE-1000-NE, FPE-1000-NW, FPR-1000-NF  

Part numbers D9124G, D9124GV2, D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4,

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9434, D7034, FPE-7034

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, FPD-7024, D7024, DS9400, DS9400I, DS9400M, D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2

  Part nummbers - FPE-1000-NE, FPE-1000-NF, FPE-1000-NW, FPA-1000-V2, FPA-1000  

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, D8512G, B9512G, D1255, D1255W, D1255R, D1255RB, B915, B920, B921C, B930, B942, D1260, D1265, B925F, B926F,

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D1256

Part numbers D10024A, D10024, D9024, D8024

In cases where RPS configuration cannot be loaded please follow the instructions from this article.

This guide gives a example of how to check that OPC is receiving commands and transmitting to controller.

Part numbers FCP-500, FCP-500-C

The FLM-325-2i4 is a Single address Dual Input Analog Addressable Module with two inputs used to monitor Normally Open (NO) or Normally Closed (NC) circuits.  If the module is addressed as 010 the First input will display as 010.1 on the panel keypad display, the Second input will display as 010.2 on the panel keypad display. 

Part Numbers, FAD-325 (DUCT Housing without Relay), FAD-325-V2F (DUCT Housing without Relay), FAD-325-R (DUCT Housing with Relay), FAD-325-V2F-R (DUCT Housing with Relay) FML-325-2R4, FML-325-2R4-2A, FML-325-2R4-2AI, FML-325-2R4-8A, FML-325-2R4-8AI, D323DH (DUCT Smoke Head), FAD-325-DH (DUCT Smoke Head), FAD-325-V2F-DH, FPA-1000, FPA-1000-UL, and  FPA-1000-V2.

In the controller history, you can see entry as detailed below, showing Detector -On- 14 , what does this indicate?

Part numbers D192C, D192G

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9431, D7039, FPE-7039