Bosch Building Technologies

    Showing results for 
    Search instead for 
    Did you mean: 
    Sort by:
    ‎05-25-2018 05:45 PM
    Part numbers EVAX25, EVAX50, EVAX100, EVAX200, EVAX150,
    View full article
    ‎05-16-2018 09:23 PM
    Part numbers D9412GV4, D7412GV4, D9412GV3, D7412GV3, D7212GV3, D9412GV2, D9124GV2,D7412GV2, D7212GV2, D9412G, D9124G, D7412G, D7212G, D9412, D9124, D9112, D7412, D7212, D192C, D192G
    View full article
    ‎03-07-2022 02:41 PM
    Option Bus NAC Outputs (FPP-RNAC-8A-4C) will never be in sync with the NAC Output of the panel (FPA-1000, FPA-1000-UL, FPA-1000-V2, or FPD-7024).
    View full article
    ‎05-11-2018 10:10 PM
    Configuring the FPP-RNAC-8A-4C on an Option Bus Fire panels FPD-7024 & FPA-1000.
    View full article
    ‎06-01-2018 10:03 PM
    AVS-44, AVS-44R, AVSM
    View full article
    ‎05-16-2018 03:14 PM
    D7038, DS9484
    View full article
    ‎05-16-2018 03:15 PM
    High Voltage (HVLT) Green - Warns of dangerous voltages when lit. Output Active (OUT) Red - Indicates that one of the NACs (1 to 4) is active. NAC Short (SHRT) Yellow - Indicates that there is a short on one of the four NAC outputs. Low Battery (LBAT) Yellow - Indicates that there is a missing or dead battery. AC OK (ACOK) Green - Indicates that the input is good and that the power supply is running from the AC line. Ground Fault (GFLT) Yellow - Indicates that the NAC output wiring has been improperly connected to an external source or ground. Loop Trouble (TBL) Yellow - Indicates that one, or both, NAC Input EOL device(s) has disconnected due to one or more of the following faults: Faulty AC power (after a delay) Low battery fault Ground fault NAC output fault EOL shorted EOL open NAC overcurrent Power supply over voltage condition
    View full article
    ‎05-24-2018 04:16 PM
    Part numbers DS9484, D7038
    View full article
    ‎06-04-2018 04:11 PM
    Part numbers D7024, D7038
    View full article
    ‎05-18-2018 03:57 PM
    Issue What could be the cause when adding four System Sensor Horn / Strobes to a Wheelock audio visual loop, and the horns are worrking fine but the strobes are not flashing correctly. Solution When installing Audio / Visual Appliances, all devices on the loop must be from the same manufacturer. Mixing System Sensor with Wheelock or Gentex or any combination may cause the Horns or the Strobes to work intermittently or not at all. This is because each manufacturer has their own Sync Pulse Protocol to run their notification devices.
    View full article
    ‎06-07-2018 03:13 PM
    Part numbers D192C, D192G
    View full article
    ‎06-06-2018 09:28 PM
    Part numbers DS9400, DS9400I, DS9400M, D7024, DS9484, D7038
    View full article
    ‎05-16-2018 03:34 PM
    The following horn strobes and strobes are listed compatible with the DS9400, DS9400I, and DS900M Fire Control Panels:
    View full article
    ‎06-06-2018 07:52 PM
    Issue Does the D7038 have built in Sync? Solution No, the Sync module is needed. The D7038 Input will pass the Sync Pulse to each Output.              Sync Module Part Numbers Brand Name                 Sync Module Part Number  System Sensor            MDL Wheelock                     DSM; SM Gentex                        AVS44; AVSM Note: If the DS9400 Series or D7024 Series panel is used with the D7038, NAC's 1 or 2 on the D7024 or DS9400 can provide a Wheelock Sync pulse. If the Eprom Revision is 2.04 or higher, either panel series can also provide a Gentex Sync Pulse from NAC 1 and or NAC 2. Part numbers DS9400, DS9400I, DS9400M , D7024, DS9484, D7038
    View full article
    ‎05-23-2018 08:07 PM
    Part numbers D192, D192C, D192G
    View full article
    ‎05-22-2018 04:30 PM
    Part numbers FPP-RNAC-8A-4C, D7038, DS9484, DS9400, DS9400I, DS9400M, D7024
    View full article
    ‎05-18-2018 04:01 PM
    Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9447, D7033, FMR-7033, FPP-RNAC-8A-4C, D7038, DS9484
    View full article
    ‎05-16-2018 03:18 PM
    The FAA-325-B6S is to be used with the FAP-325, FAI-325 and FAH-325 model sensors only. The FAA-325-B6S provides an audible alarm in the immediate vicinity. Typical applications are for use in hotels, apartments, and hospitals. It is compatible with the FPA-1000, FPA-1000-UL, and FPA-1000-V2.
    View full article
    ‎05-22-2018 04:25 PM
    Part Number D192C - Replacement is D192G
    View full article
    ‎05-25-2018 04:45 PM
    Part numbers AVS-44, AVS-44R
    View full article