Fire

Part numbers D2071A, DS9471, 911A, 911AC, D2071AC, D2071AHC, D2071ACPL-1, D2071ACT, D2071AH

Part numbers D10024A, D10024, D9024, D8024, D322A

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4, DS7447, DS7440

Issue What are the proper steps in cleaning a DS200HD smoke head? Solution Turn off all electrical power to the detector. Depress the tab on the two sides of the detector adjacent to the LED, and pull the unit from its base. Fill three (3) clean buckets each with 1-1/2 gallons normal tap water. NOTE: De-ionized or distilled water is preferable in areas where hard water with large mineral content is prevalent. Add one (1) teaspoon of dishwashing liquid (Ivory Dishwashing liquid only) to the first bucket and mix thoroughly, then place the dirty detector into the soapy water until it is completely submerged. Allow the unit to soak for approximately ten (10) minutes, then agitate to insure all dust and dirt is removed. Remove the unit to the first clean water bucket, submerge detector and agitate for 5-10 seconds to remove all soap residue. Finally, move unit to the second clean water bucket, and repeat the procedure in step #5. Remove from second bucket, then vigorously (not violently) shake unit to drain all water. Remove unit to dry area and allow to drain and dry by resting unit on its side. Allow unit to dry for a period of 72 hours before use. Caution: Air Dry units only. Do not use any hot air device or attempt to place unit in oven, as this will result in damage to the detector. Also wash and rinse water should be changed every 5-7 units to maximize the results.

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4, DS7420I

Part number D9142F

Part numbers DS9400, DS9400i, DS9400M, D7024, FPD-7024, DS9431, D7039, FPE-7039

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4

Issue Control trouble # 87 displays Battery Trouble. Probable Cause: The battery failed a battery test The battery is defective The wiring to the battery is disconnected Solution: If there has just been a power failure, wait a least 24 hours for the battery to recharge, then perform a system reset to re-test the battery and clear the error Replace the battery. Check wiring.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9431, D7039, FPE-7039, D7053, D7035

Part numbers D10024A, D10024, D9024, D8024, D9051, D9068

  Issue The D192G panel zone (point) is in trouble and the yellow LED is not on. Solution With the zone/point in trouble and No Yellow LED On there is a wiring fault. One of the following terminals do not have power connected to them. External Power In (EXT PWR IN) and / or Auxiliary Power In (AUX PWR IN). Terminal 1 (AUX PWR IN) 13.75 VDC Terminal 2 (Common) Terminal 3 (Supervised Zone / Point) 2.50 VDC Normal Condition < 1.50 VDC In Trouble condition Terminal 4 (Trigger) 13.75 VDC In Alarm Only Terminal 5 (External Power In) 12 VDC or 24 VDC Depended on needed Output for the NAC's or Power Supply Terminal 6 (Common) This is the Common from an 24 VDC External Power Terminal 7 (Positive Alarm Output) Terminal 8 (Negative Alarm Output) Part number D192G

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4

 Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4

Part numbers D7024, DS9400, DS9400I, DS9400M

Part numbers D10024A, D10024, D9024, D8024

Part numbers D192C, D192G

Part numbers D2071A, DS9471, 911A, 911AC, D2071AC, D2071AHC, D2071ACPL-1, D2071ACT, D2071AH

Part numbers DS9400, DS9400I, DS9400M, D7024, DS9484, D7038