Fire

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9465I, MX465, D7035, D7053

Part numbers D9412GV4, D7412GV4, D9412GV3, D7412GV3, D7212GV3, D9412GV2, D9124GV2,D7412GV2, D7212GV2, D9412G, D9124G, D7412G, D7212G, D9412, D9124, D9112, D7412, D7212, D192C, D192G

Panel part numbers DS7400XIVER3+, DS7060, DS7090, DS7090I, DS7090TM, DS7080I, DS7080IVER2, DS7080IP32, DS7090TMI, DS7100, DS7400, DS7400XIVER2, DS7400XIVER4+, DS7400X, DS7400Xi

Part numbmers D9051, D9070, D9070A, D9070B, D9069, D9069A, D9069B, D10024, D10024A, D8024, D9024

Issue - Can the MUX data loop be run in the same cable of wire as the Keypad data wires? Solution - They cannot, they are two different data outputs.  They should never be run in the same jacketed of wire. They each require their own wire run and should at least 3 inches apart in the raceway. Part numbers DS7400X, DS7400Xi, DS7400, DS7400XIVER3+, DS7400XIVER4+, DS7400XIVER2, DS7430, DS7436, DS7447

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part numbers FPC-500, FPC-500-P, FPC-500-C, FPC-500-C-P

Part numbers FPD-7024,  D7024, DS9400, DS9400I, DS9400M, D7053, D7035, DS9465I, MX465, DS9432,

 Technical Bulletin FPD-7024 System Trouble Event Table Correction

Part number FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9431, D7039, FPE-7039

Part numbers F220-B6C, F220, F220-B6R, F220-135, F220-135F, F220-190F, F220-P, F220-PTH, F220-PTHC

Part numbers P1224MC, P1224MCK, P1124MCW, S1224MC, S1224MCK, S1224MCW

Part numbers D9068, DS9602, DCT-1, DCT-1E, FPT-DACT, FMR-DACT-KEYPAD, D7033, DS9447

 Tecnical Bulletin D7053 Relay not Resetting after a Trigger FPD-7024 Firmware 1.00

The programmer for the DACT family (D9068,FPT-DACT; DCT-1; DCT-1E; DS9602) is one of the following: D7033 DS9447 FMR-DACT-KEYPAD Notes The FMR-DACT-KEYPAD is not the same as the FMR-7033. The FMR-7033 will not program the D9068 DACT family (FPT-DACT; DCT-1; DCT-1E; DS9602).

Part numbers DS240, DS241, D296, D297,

Part numbers D125B, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9112G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, 7412GV4, D9412GV4, B8512G, B9512G

The following horn strobes and strobes are listed compatible with the DS9400, DS9400I, and DS900M Fire Control Panels:

 Program Menu for the DS9400, DS9400I and DS9400M

Use the program menu tree shown below to program D9068 using the FMR-DACT-KEYPAD or D7033 Programming Keypad.