Fire

Part number D9133TTL-E, C900TTL-E

Issue What could be the cause when adding four System Sensor Horn / Strobes to a Wheelock audio visual loop, and the horns are worrking fine but the strobes are not flashing correctly. Solution When installing Audio / Visual Appliances, all devices on the loop must be from the same manufacturer. Mixing System Sensor with Wheelock or Gentex or any combination may cause the Horns or the Strobes to work intermittently or not at all. This is because each manufacturer has their own Sync Pulse Protocol to run their notification devices.

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part Numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER3+, DS7400XIVER4+, DS7400XIVER2, DS7447I, DS7447E, DS7447

To silence all NAC's of one panel (FPA-5000/Avenar) from the map in FSM Step-by-step guide   Insert a sensor on the map of FSM Under sensor properties choose: General: Add symbol: FIRE_Panel_FPA_BG Settings: Driver Instance: the panel / compound where the FSM is belongs to Address-> e.g. Panel 1-10.1 ! Please pay attention: there are other “Panel” possibilities to choose. Please do not choose Panel 1-10 (Communication)! After inserting the settings click “ok” Then Apply At the map when you right click the panel symbol you will get the commands as shown below.   If there is a fire alarm, you can right click at the panel and then click at “silence on”. Please be sure, that then every NAC which is belonging to this panel is “silenced”. Additional: there is also a command "silence scope" which then has the effect, that the whole scope will be silenced.

This article discusses how to send reports to the CS (Central Monitoring Station) from the FPA-1000-V2. We can network up to 8 of the FPA-1000-V2 panels together.  Each panel can report to the CS by itself, or one panel can report for all.  In either configuration, each panel needs its own unique account number.  

How to replace existing map or background on FSM client?

Is the status displayed when Supervisory Usage type is selected in RPS - Bosch Fire Monitoring System?

Any related HW change in the FSM server will lead to license not being valid and will need to be transferred.

Part numbers D192C, D192G

Part numbers DS9400, DS9400I, DS9400M, D7024, DS9484, D7038

Issue Does the D7038 have built in Sync? Solution No, the Sync module is needed. The D7038 Input will pass the Sync Pulse to each Output.              Sync Module Part Numbers Brand Name                 Sync Module Part Number  System Sensor            MDL Wheelock                     DSM; SM Gentex                        AVS44; AVSM Note: If the DS9400 Series or D7024 Series panel is used with the D7038, NAC's 1 or 2 on the D7024 or DS9400 can provide a Wheelock Sync pulse. If the Eprom Revision is 2.04 or higher, either panel series can also provide a Gentex Sync Pulse from NAC 1 and or NAC 2. Part numbers DS9400, DS9400I, DS9400M , D7024, DS9484, D7038

Part numbers D10024A, D10024, D9024, D8024

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

DS7400Xi Version 3 and DS7400XI V3+

Question   Do Bosch addressable smokes and smoke bases support CleanMe functions?   Answer   Currently the only Bosch smoke detector that supports CleanMe functions is the F220 series smoke heads when used with a conventional two-wire (F220-B6) base only and a CleanMe enabled control panel such as the D7024, and FPD-7024 conventional zones. Note:  The D7050, D7050TH does have a Chamber Check feature that will report dirty smoke if the head needs cleaning when used on the D7024, FPD-7024, DS9400m, DS9400, DS9400i.

D282A

Part numbers D7024, FPD-7024, D7042, D7052, D7053

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9434, D7034, FPE-7034

Part numbers D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2, D192C, D192A,