About rlarkins

You can create an audit log report for all or specific users by logging into System Administration. Select Administration | Reports. Select the Report Configuration tab, and then scroll down until you see User Transaction Log or User Transaction Log by ID. Once you select the desired option, then select Preview or Print at the bottom. For further assistance please contact Lenel: 1-800-631-6046 ... View more

 Follow the steps below to add the additional reader board. Power down the system. Remove the shunts from the termination jumpers on all previously existing reader boards.  The jumper pin block is labeled JP1. Mount the additional reader board into an AEC "additional" enclosure. Stacking boards on top of existing ones is not supported. Shunt the termination jumpers on the last board along the RS-485 bus.  The jumper pin block is labeled JP1.  Note, this is the last board on the physical data bus.  It doesn't have to be the last address as addresses are permitted to be out of order on the loop. Address the additional reader board using the dipswitches.  The valid addresses are 1, 2, 3, and 4. Wire in the RS-485 communications wire between boards using terminal block T13 on each board.  The bus must be daisy chained and cannot be t-tapped or wired in a star topology.  The wires will be connected "straight through" with A --> A, B-->B, and Shield --> Shield.  Wire the ground to the enclosure's ground. Attach the tamper and main power fail input wires to T12 on the additional reader board.  If unused, shunt the inputs with a shorting wire. Power up the system and wait for a full reboot. (5 to 8 minutes) Log in to the web interface and browse to Configuration | Device | Door. Click on the green '+' sign at the top left to add a new door. Click on the green '+' sign next to the Entry drop-down box. Put a check in the box next to the reader board you added. NOTE:  If the reader board is still is not responsive in the system, browse to System | System Log and click on the circular button for "Re-Scan the Available Reader I/O Boards."  Wait 3 minutes for the system to scan and refresh the screen. ... View more

The door on my intrusion panel opens whenever I press the '#'key for an invalid or valid card read. One thing to check would be the programming of the panel and make sure there are no users under the passcodes who have their master site code as blank. ... View more

I cannot connect to any panel using RPS. I have done the following: tried all settings and addresses and tried different panel types.I have ensured the laptop was disconnected from ac power and the fire wall was turned off. I have ensured there were no active wireless connections but I am still unable to connect over the phone, network, cell or over the DX4010V2. A possible solution is that a second instance of RPS is running on the computer. To correct the problem, shut down both instances of RPS. Log off and then log back into RPS. A successful connection may work with the control panel via RPS ... View more

The D6100 does not support a Conettix Failover Solution.  The Conettix Failover Solution requires that the backup receiver has one Ethernet device configured with the same MAC address as the primary receiver, and a second Ethernet device configured to be on the network at the same time as the primary receiver.  Because the D6100 only supports one Ethernet connection and it is the built in Ethernet adapter, a failover solution is not possible. © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages. ... View more