You will find a Operations- Guide for this Community in the attachments.
Please note: Articles are created by Bosch BT employess only!
Mainly members of
-Technical Support(Solution Groups or Development Groups)
- Product Management
- Service Project Leaders.
... View more
There are different ways for a client to receive a multicast stream:
the client can connect to the camera and request a multicast stream. In this case you would see a connection in the dashboard.
If not checked, it requires at least one connected client to have the camera provide the stream into the multicast group. Clients who just joined would receive no stream if there is no client connected.
the client can join an existing multicast stream without connecting to the camera. It must know the multicast group. You would not see this client on the dashboard.
The streaming flag tells the camera if it should feed its stream into this multicast group, regardless of a connected client. This is an option if there are many, many clients possibly connecting to the same camera/stream.
There is no difference in data amount if streaming is checked or not as long as there is at least one multicast client connected to this multicast group.
Below you find a way how to pass a special connection string to request a multicast stream via RTSP from a BOSCH IP camera or IP encoder.
The following string triggers the connection to be multicast stream using the multicast IP and port that were predefined in the configuration before.
see device webpage --> Settings --> Network --> Multicasting
If you want to get the multicast stream on a specific IP and port (e.g. IP 18.104.22.168, port 1234) you can use following syntax:
rtsp://192.168.0.1/&multicast_video=1&mc_group_video=22.214.171.124&mc_port_video=1234 You can also use the RTSP SETUP command to enable multicast streaming. Note: Forwarding the RTSP port using RTSP SETUP command is supported with firmware 5.50 and later.
There is also a posibility to use SDP file:
You should configure the encoder to create cyclic I-frames, do not leave it on auto but set e.g. to 30.
Enter a multicast group address and set the streaming checkbox.
Then record the connection setup with Wireshark and save the relevant info as SDP file locally. Then, the payload type should be correct.
If necessary, edit the SDP file to match your intended multicast group address and port , and check the payload type which should be 35 for H.264.
There are two locations in the file for the payload type.
Then open the file in VLC.
The SDP file should look like this:
o=- 0 0 IN IP4 <ipaddress>
m=video 60010 RTP/AVP 35
c=IN IP4 126.96.36.199
Alternativly, there is an undocumented (thus untested and without guarantee that it is fully functional) feature in our devices that allows to download an SDP file:
http:// < ipaddress > /live.sdp?line=1&h26x=4 via browser and save it locally.
Edit the file as nessesary and open in VLC.
PDF: Please see also the attached PDF from year 2016 which is still of help these days
... View more
Related Products RPS 5.12 Overview Helps when encountering error 'SQL BPA Command line has encountered a problem and needs to close' when running the Windows Installshield Wizard for Microsoft SQL Server 2005 Express Edition Server Pack 3 (SP3). Issue If you open the Application Event Log in the event viewer after the failure, you can notice the error below: The error 29552 indicated in the MsiInstaller error means that the Upgrade Advisor (SQL tool used during setup) encountered a problem when dealing with Reporting Services. If you open the RS.log log file located under C:\Documents and Settings\Administrator\Application Data\Microsoft\SQL Server 2005 Upgrade Advisor\log, you can get more information about what leads the Upgrade Advisor to fail. This indicated that the BpaCmd.exe command line (called by the Upgrade advisor) failed because it couldn’t locate the file BPAClient.dll (causing the FileNotFoundException exception). Solution There is a simple workaround that you can use in order to achieve the setup of SQL Server 2005 Express Edition Service Pack 3 with success. Here are the steps of the workaround: Copy the BPAClient.dll file located under 'C:\Program Files (x86)\Microsoft SQL Server\90\Setup Bootstrap\BPA\bin' to: 'C:\Program Files (x86)\Microsoft SQL Server\90\Setup Bootstrap\BPA'. Run the SQL 2005 SP3 setup again. Notes
... View more
Related Products ReadykeyPRO Question What effect does losing communication with the server have on an access controller? Answer The ISC has its own memory, and it will run locally from its own database. The ISC itself will not be effectedÂ by a communication loss unless it runs out of transaction memory, or it operates any global functions. Any readers providing access without global anti-passback will not be effected. When the ISC has an upstream communication failure with the communication server and/or linkage server, global features will cease to function. This includes features such as Scheduler, Guard Tour, Global Anti-Passback, and Global Input/Outputs. If there is a failure upstream to the communication server from an ISC, the linkage server, global output server, and any other server service that requires activity from the offline access panel will not run any functions associated with the events from that panel (i.e. an e-mail will not be sent on an Access Granted from the ISC if the ISC is offline with the communication server).
... View more
Related Products Readykey Pro v6.1 Question Can Readykey Pro use custom barcode fonts in Badge Designer? Answer No, custom barcode fonts cannot be created in Badge Designer. There is a built in Barcode Object in Badge Designer that can allow barcodes to be printed on badges. There are a number of supported formats: Codebar Code 128 Auto Code 128-A Code 128-B Code 1280C Code 3 of 9 2:1 Code 3 of 9 3:1 Code 93 EAN-13 EAN-8 Extended Code 3 of 9 2:1 Extended Code 3 of 9 3:1 Extended Code 93 Interleaved 2 of 5 3:1 PDF417 POSTNET UCC-128 UPCA
... View more