About VS-Support-AP

Related Products All IP encoders   Question   Can I use Alarm Task Script for JPEG post to FTP every 30 minutes?   Answer   Copy/ Paste this example into the alarm task editor and save.  See comments below for more details, annotated by //. // Settings for JPEG posting JpegPosting PicPosting := { IP( "put ftp FQDN servername or IP here" ) Login( "anonymous" ) Password( "anonymous" ) Format( Large ) FileName( "Snap" ) Suffix( Date ) Camera( All ) }; // Define Operation Mode to periodic, 15min low and 0.1 second high OperationMode periodic := { Low(18000) High(1) }; //define logic TempState(1):=periodic; if(true) then TempState(1); if (TempState(1)) then PicPosting; ... View more

Related Products Bosch encoders   Step-by-step guide   Place this in the alarm task editor and save it.  Please read the comments for more details.  They are noted below by //.   //Define weekly timer from Monday to Sunday from 7am to 9pm Timer weekly := {TimeBegin(07:00) TimeEnd(21:00) DayBegin(Mo) DayEnd(Su) }; //define what is to be recorded Recording recording:= { Camera(All) }; // Define Operation Mode to periodic, 1 sec low 30 min high OperationMode periodic := { Low(10) High(18000) }; TempState(1):=periodic; //define recording timer OperationMode monostable := {High(50)}; TempState(2):=monostable; //Turn on recording timer if (IsActivated(weekly)) then TempState(1) := true; if (TempState(1)) then TempState(2) := true; if (TempState(2)) then recording else Stop(recording); ... View more

Question   How many streams can use the BP+ profile? Related Products VIP-X1 XF   Answer   Only 1 stream can have a BP+ profile assigned. BP+ (Baseline Profile +) is available in any of the new ARM based chipset encoders, like the VIP-X1 XF.  BP+ is needed for compatibility with Divar and hardware decoders, for example, theVIP XD decoder. ... View more

Related Products NetApp disk arrays   Question   How can you configure singe mode VIF on NetApp array? For example if we have 2 (or more) physical interfaces, how to connect them to different network segments and, if one of the segments fails, the second network interface to step in automatically?   Answer   Remark: You may need to read the article (How can you set up the redundant network connection for a NetApp array?) first. A single-mode VIF contains a single active link and a number of links in passive mode. All links in the single-mode VIF share a single MAC address. Only one link is active and sending data therefore there is never a duplicate MAC address on the network. A single-mode VIF is configured with two links connected to redundant switches. Only link e0 is active, while the e1 is in standby mode. If e0 fails (signaled by the link status of the interface going down), the remaining link will take over. In the case of multiple standby interfaces, the storage device will randomly pick one to bring up as the active link. This is commonly known as active passive mode. (source NetApp Technical report TR3802). For detailed information and configuration instructions, please see Part 4 IMPROVE PERFORMANCE AND RESILIENCY WITH PORT BONDING (4.1 SINGLE MODE VIF) of the Technical Report: Ethernet Storage Best Practices, January 2010, TR3802 on www.netapp.com  Please note: the Bosch - NetApp disk arrays are shipped with two Ethernet ports as default   ... View more

Question   What are the restrictions of VRM Configuration utility pre-installed on DLA? Related Products DLA - disk array series Configuration Manager   Answer   Advanced configuration must not be done via VRM Configuration utility pre-installed on the DLA. The reason is that DLA is a Server Appliance platform and contains no VideoSDK installation. Advanced configuration should be done by VRM Configurator installed on a separate computer. The installer is stored at the directory: “C:\Bosch\Resources”. ... View more