Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Conference & Discussion

    Sort by:
    ‎04-06-2021 11:56 AM
    Description: The RESTful API of the CCS1000D is used in order to get a clear view of the state of the discussion devices’ microphones (amongst other things). However, when a Priority call is made, the other speakers still show as active even though they are muted in reality. Solution: This is actually as it' supposed to work. The reason the speakers still show as active is because they remain in the speaker list while the priority call comes through (in this case, the chairperson making an announcement overruling all other parties) is that in the system there’s a difference between speakers being muted and speakers being removed from the speaker list. In this case, after the priority call ends, the speakers are unmuted and can resume the discussion. It’s also possible to configure the system to stop all speakers and remove all waiting participants from the request list. If the system is setup in this way and the chairperson starts speaking, the system will indeed erase all other speakers and waiting speakers. The API can be used to create a custom interface. This means that logic can be added so the preferred outcome is created. In this case it means that the custom interface needs to poll for the speakers list but also needs to take in account that when a priority call comes through (also pollable) this means the others are muted. Using these two givens can then be used to for example change the icons of the speakers to a ‘muted’ state in the custom interface.
    View full article
    ‎04-06-2021 11:56 AM
    Product(s) affected: DCN-NG systems with master & slave CCU set-up Version(s): all Problem description: A DCN-NG system will be installed in a building which uses different VLANs for different floors in the building. They want to be able to have interpreters on one floor (in one VLAN) and the rest of the system on another floor (in another VLAN). To this end they have connected their Master CCU to another VLAN than their Slave CCU. This set-up does not work. Question is; should this work and if not, why not? Solution: This cannot work in a DCN-NG system because of the way the system is designed. The communication between the CCU’s, at start-up of the system, uses broadcast messages which are not routed by network devices. These messages have a time-to-live (TTL) of 1, which means that once they attempt to cross into another (V)LAN, the messages are not propagated by the routing (L3) switch. The reason is that the TTL of the packet is decreased every time it traverses from one network to another. When the TTL’s value reaches 0, the packet is dropped by the routing device. Therefore, the broadcast packet will never reach the other CCU, resulting in error messages like “No Master CCU” on the Slave CCU. Therefore the system should be installed on the same (V)LAN. This usually does not pose any technical problems as (V)LANs can be distributed over multiple network devices without issue, it’s just that the predictability of where a device is physically located is less in this instance.
    View full article
    ‎04-06-2021 11:55 AM
    In order to integrate 3 rd party software with the DCN-NG system, there are 3 different integration options: Open Interface (OI) Application Programming Interface (API) Streaming Meeting Data (SMD)
    View full article
    100% helpful (1/1)
    ‎04-06-2021 11:53 AM
    The request was to integrate an AMX NX-2200 with the CCU2. The appropriate licenses were installed, but the devices cannot communicate through the serial connection.
    View full article
    ‎04-06-2021 11:53 AM
    Audio is disrupted in a multi-CCU system, most likely after first install, re-install or reset of a multi-CCU system.
    View full article
    ‎04-06-2021 11:49 AM
    In order to change the layout, the StyleSheet needs to be changed. Default it is located in C:\ProgramData\Bosch\DICENTIS\VotingResult.xslt, this file can be opened in any text editor, Notepad++ is recommended as it is very versatile.
    View full article
    ‎04-06-2021 11:39 AM
    System setup with multiple cameras and a supported multiviewer: Orange: Ethernet connections, red: audio or video connections, blue: HD-SDI Follow the manuals for the multi-viewers. They can be found at their manufacturer’s websites: TvOne Corio Matrix Mini User Manual Kramer MV 6 User Manual Make sure that to get this setup to work, both the multi-viewer and the CCS1000D Control Unit should be in the same VLAN/subnet. Also, use the correct port to connect to the multiviewer: TvOne Corio Matrix Mini; port 10001, example: http://192.168.1.2:100001 Kramer MV 6; port 5000, example: http://192.168.1.2:5000
    View full article
    ‎04-06-2021 11:38 AM
    When upgrading from a previous DICENTIS version that supports DANTE (V2.20 – V3.00) to the latest version 3.10, the following problem will occur; The DICENTIS system is not visible anymore in the Audinate’s DANTE controller software, where it was visible before the upgrade.
    View full article
    ‎04-06-2021 11:37 AM
    Question Can a CCU be used in the same DCN-NG system as a CCU2 or CCUB2? Answer No, this is not possible. Mixing CCUs and CCU2/CCUB2s in a DCN-NG system is not supported. It’s also not possible to use a CCU as a spare unit in case of failure of a CCU2/CCUB2 in a DCN-NG system.
    View full article
    ‎04-06-2021 11:35 AM
    In order to add authorizations to an existing license, the current license key is required as well as the new authorization numbers. How to find this key is detailed in another article: How to find the license key loaded in a DCN-CCU2 Follow the next steps for adding the new authorizations: Go to https://license.boschsecurity.com Fill in the CCU's Serial Number and CHK: Enter the current license key (this is found on the license key document received after activating the previous authorization numbers). In the following windows the license information is shown and it's possible to add additional authorization numbers. If multiple authorization numbers need to be added, choose "Next Authorization" If all authorization numbers are added, choose "Finish register" Next window will give the opportunity to register a spare CCU if applicable. A last verification is done in the next window, if things need to be changed, the process goes back to step 4. The license key with all information is shown on the next page. Note that the Print button doesn't work in all browsers, for this refer to "Printing the License Key document to PDF" Upload the license key into your CCU or NCO. The Bosch ‘download and license tool’ is to be used to upload your license into a CCU2.
    View full article
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist