Fire

Can the installer code be returned to default in the FPD-7024, D7024, DS9400, DS9400I, DS9400M fire panels?  

How to configure the FPD-7024 to communicate by phone using keypad programming. How to use keypad programming to configure the FPD-7024 for phone communications.

How to use the DX4010V2 for connecting to the FPD-7024 with RPS. How to correct the FPD-7024 indicating Trouble Missing DX4020 or DX4010V2.  

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M,DS9431, D7039, FPE-7039

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9431, D7039, FPE-7039

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part numbers FPD-7024, B426, B420, DX4020, B450, B440, B441, B442, B443, B444

How to interpret DBL when displayed on the FPD-7024 or D7024.

This article provides instructions for troubleshooting Ground Fault in the FPD-7024 or D7024

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9447, D7033, FMR-7033

Follow the steps from this article to configure FPD-7024 to communicate using Cellular or Ethernet network communications. How to configure the FPD-7024 for network communications using keypad programming.

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9431, D7039, FPE-7039

How to correct the FPD-7024 or D7024 error: Programmed Points Exceeds Max. How to correct the FPD-7024 or D7024 error: PRGRMMD POINTS EXCEED MAX.

A sticker on the front of the B450 indicates proper switch positions for selecting various SDI or Option Bus addresses (see figure 1). Figure 1 Sticker with address configurations   There are 2 types of FPD-7024 panels. It must first be determined which is in use before selecting the B450 address: Newer types with firmware version 1.06 and higher. These types are identified by icons on the keypad instead of words (see figure 2). Older types with firmware version 1.03 and lower. These types are identified by words on the keypad. Figure 2 Version 1.06 with Icons vs 1.03 with words   Version 1.06 & newer types: When used as sole communicator or backup to phone line, set the address wheel at 9 for Option Bus address 250. When used as backup to a primary network communicator, set the address wheel at 6 for Option Bus address 134. RPS connections require Option Bus address 250. Be sure the address wheel is set at 9 on the network communicator intended for RPS connections (Ethernet is preferred when allowed). Version 1.03 and older types: Use Option Bus address 250. Only one network communicator is available on these panel types.

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M,

Part numbers D7052, D7024, FPD-7024, DS9400, DS9400I, DS9400M, MX363

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M,FPP-RNAC-8A-4C, DS9484, DS9488, D7035