Fire

When using Wheelock / Cooper / Eaton Exceeder LED 3 Strobes and Horn Strobes on a UL Listed Bosch Fire panel a DSM or SM Wheelock Sync Module is required.

Part numbers FPD-7024,  D7024, DS9400, DS9400I, DS9400M, D7053, D7035, DS9465I, MX465, DS9432,

 Technical Bulletin FPD-7024 System Trouble Event Table Correction

Part numbers FPA-1000, FPA-1000UL, FPA-1000-V2

D2071, D2071A, D2071AC, D2071ACP, D2071ACPL-1, D2071ACT, D2071AH, D2071AHC, DS9471, D5200, D911, D911A

Part number FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9431, D7039, FPE-7039

Part numbers F220-B6C, F220, F220-B6R, F220-135, F220-135F, F220-190F, F220-P, F220-PTH, F220-PTHC

Part numbers P1224MC, P1224MCK, P1124MCW, S1224MC, S1224MCK, S1224MCW

Part numbers D9068, DS9602, DCT-1, DCT-1E, FPT-DACT, FMR-DACT-KEYPAD, D7033, DS9447

 Tecnical Bulletin D7053 Relay not Resetting after a Trigger FPD-7024 Firmware 1.00

Part numbers FPA-1000, FPA-1000-UL, FPA-1000-V2

Part numbers FPD-7024, B426, B420, DX4020, B450, B440, B441, B442, B443, B444

D7038, DS9484

High Voltage (HVLT) Green - Warns of dangerous voltages when lit. Output Active (OUT) Red - Indicates that one of the NACs (1 to 4) is active. NAC Short (SHRT) Yellow - Indicates that there is a short on one of the four NAC outputs. Low Battery (LBAT) Yellow - Indicates that there is a missing or dead battery. AC OK (ACOK) Green - Indicates that the input is good and that the power supply is running from the AC line. Ground Fault (GFLT) Yellow - Indicates that the NAC output wiring has been improperly connected to an external source or ground. Loop Trouble (TBL) Yellow - Indicates that one, or both, NAC Input EOL device(s) has disconnected due to one or more of the following faults: Faulty AC power (after a delay) Low battery fault Ground fault NAC output fault EOL shorted EOL open NAC overcurrent Power supply over voltage condition

FPD-7024, D7039

The programmer for the DACT family (D9068,FPT-DACT; DCT-1; DCT-1E; DS9602) is one of the following: D7033 DS9447 FMR-DACT-KEYPAD Notes The FMR-DACT-KEYPAD is not the same as the FMR-7033. The FMR-7033 will not program the D9068 DACT family (FPT-DACT; DCT-1; DCT-1E; DS9602).

Part numbers DS240, DS241, D296, D297,

Part numbers D125B, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9112G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, 7412GV4, D9412GV4, B8512G, B9512G

The following horn strobes and strobes are listed compatible with the DS9400, DS9400I, and DS900M Fire Control Panels:

 Program Menu for the DS9400, DS9400I and DS9400M