Fire

The following horn strobes and strobes are listed compatible with the DS9400, DS9400I, and DS900M Fire Control Panels:

 Program Menu for the DS9400, DS9400I and DS9400M

Use the program menu tree shown below to program D9068 using the FMR-DACT-KEYPAD or D7033 Programming Keypad.    

Part numbers - FPA-1000, FPA-1000-UL, FPA-1000-V2, FLM-325-CZM4

Part Numbers FPA-1000, FPA-1000-UL, FPA-1000-V2, FPE-1000-SLC

Part Numbers FPA-1000, FPA-1000-UL, FPA-1000-V2, FLM-325-IM, FLM-325-I24, FLM-325-I24-A, FLM-325A, FLM-325, FLM-325A-D,

Part Numbers - D7024, FPD-7024, DS9400, DS9400I, DS9400M

Bosch part numbers D340, DS290, D263, D263TH, D263THC, D263THS, DS282, DS282TH, DS282THC, DS282THS, F220-B6, F220-P, D287, D288, D285, D285DH

Wiring the F220-B6PS and F220-B6PM bases. Wiring F220-B6PM with F220-B6 Slave bases.

Part Numbers D7024, FPD-7024, DS9400, DS9400I, DS9400M

Part Numbers D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, D192C, D192G

Part Numbers FPA-1000, FPA-1000-UL, FPA-1000-V2, D10024A, D10024, D9024, D8024, D328, D328A, D327, D327A, FLM-325-N4, FLM-325-2R4, FLM-3252R4-A2, FLM-325-R24-A8

Part Numbers D10024, D10024A, D9024 ,D8024, D326 ,D326A, D334 ,D334A, D339, D339A  

Part Numbers D9068 (DACT Dialer), D9052 (Interface Module for Serial DACT Connect to the Morley Panel), D10024A, D10024, D9024, D8024 (Morley Fire Panels), D7033 and FMR-DACT-KEYPAD (Keypad Programmer for the D9068

How to correct the FPD-7024 or D7024 error: Programmed Points Exceeds Max. How to correct the FPD-7024 or D7024 error: PRGRMMD POINTS EXCEED MAX.

FPA-1000, FPA-1000UL, FPA-1000V2, FMR-1000-RCMD, FRM-1000-RA

Part Numbers of old Morley Fire Panels -  D10024, D10024A, D9024, D8024. Part Number of the Loop Card (SLC Card) D9067.

FPA-1000, FPA-1000UL, FPA-1000V2, Panel Grounding, Ground Fault

Part number list, DS9400, DS9400I, DS9400m, D7024, FPD-7024, D7053, D7035, D7039, FPE-7039,DS9431, DS9431R, MX465, DS9465, DS9465I, DS9432.

The D305 does not have the ability to trip the control panel or smoke head into alarm. The D305 Test Plate only toggles the alarm LED and relays of the D332A, FAD-325-R and FAD-325-V2F-R. The only way to get the control panel to display an alarm or supervisory  from the Analog Hochiki DUCT Detectors is by using UL Listed canned smoke (refer to the testing procedure below). Currently the only work-around is to connect a single point module (D334A, D339A, FLM-325-IM, FLM-325-I4, FLM-325-I4-A or FLM-325-I4-AI) to one of the alarm relays of the D332A, FAD-325-R or FAD-325-V2F-R. *Note: If the customer installed the D331A, FAD-325, or FAD-325- V2F we have no way of using the D305 to trip the panel into alarm.  Option 2 - Replace the DUCT Housing (D331A, D332A, FAD-325, FAD-325-R, FAD-325- V2, or FAD-325- V2-R) and Test Plates (D305) with D341P Conventional DUCT Housing with Head, D344-RT Remote Test Plate, and D339A, D334A, FLM-325-IM, FLM-325-I4, FLM-325-I4-A or FLM-325-I4-AI Analog Single Point Monitor Module. The downside is that the customer will lose the ability to read the sensitivity of the DUCT through the control panel web-browser. Testing  Procedure (D331A, D332A, FAD-325, FAD-325-R, FAD-325- V2, or FAD-325- V2-R) Install the detector housing. The green Pilot LED on the housing’s front lights. Remove the head. The Pilot LED goes out to indicate head supervision. Replace the head and reset the FACP. Test the detector’s operation. Light a piece of clothesline and place it approximately 3 in. (7.6 cm) from the head. Blow across the lighted area toward the detector head. The Alarm LED lights within 1 min and the two alarm relays energize shorting Terminal 8 to 9 and Terminal 11 to 12. Reset the housing. The detector momentarily resets and returns to the alarm condition. Perform this operation several times. After 5 min, the smoke in the detector head clears and the detector remains reset. Replace the cover.